# Winding Sticks Hewn Tool Library · https://hewn.build/tools/winding-sticks Corrected: An independent reviewer read this entry and found corrections. They have been applied to the text, and the reviewer re-checked the correction that mattered most for safety and found it done; the others have not been re-checked yet. The list at the end is the record of what changed. Cite as: "Winding Sticks." Hewn Tool Library, hewn.build/tools/winding-sticks. Reviewed 2026-08-01. --- ## identity - **name:** **Winding Sticks** (also "winding strips" or "wind sticks"; Paul Sellers calls the practice "rack o' th' eye" [WS11], a phrase attributed to him here, not established as period terminology) — a matched pair of narrow, straight, parallel-topped battens laid across a board, panel, or assembly at each end (or at two chosen reference points) and sighted across, one behind the other, so that any twist ("wind") in the surface between them is visually amplified into an easy-to-read misalignment of the two sticks' top edges [WS4][WS9][WS11]. - **family / category:** Measuring & layout → the reference-standard branch, a paired sibling of the [[Straightedge]] but built to read a genuinely different geometric property (twist, not flatness-along-a-line) [WS4][SE-cross]. - **one-line:** Two matched sticks that turn an invisible twist into something the eye can't miss — the tool exists because a board, a glue-up, or an assembly can pass every other flatness check and still rock on the bench, and only a sighted comparison across a span catches it. --- ## ✦ how NOT to use it - **not-for:** - Checking overall flatness of a single face along its length — that reads as flat/straight via a [[Straightedge]], not via winding sticks (see *matching → cannot replace*) [WS19][SE-cross]. - Checking plumb or level as a visual amplifier — a different instrument; see *lineage-misuse* for the conditional spirit-level screening use. - Trusting a twist reading when the sticks are not seating stably — see *beginner-trap* below [WS14][WS19]. - Using the sticks in place of the manufacturer's alignment procedure on a jointer or planer, or placing them on machine tables with the machine connected to power — see *dangerous*. - **dangerous:** - **The sticks themselves have low inherent hazard.** No blade, no motor, no stored energy. A research search for injury literature specific to winding sticks found none; that is a search result, not a risk assessment, and it says nothing about the machines the sticks are used near. - **Use on a jointer or planer is the hazard that matters.** Table-alignment work puts the user near the cutterhead and may involve removing or displacing a guard. Controls, in order: - **Disconnect the machine from power** (unplug it), **prevent restart, and wait for all motion to stop** before placing anything on the tables or reaching near the cutterhead; WOOD Magazine's jointer tune-up instructs unplugging before table alignment, and model manuals likewise require disconnection from power [manual, relayed][WS31]. The WOOD Magazine page could not be fetched in this pass. - **Follow the model's manual before removing or displacing any guard or working near the cutterhead.** Put guards back before the machine is reconnected [manual, relayed]. - **Treat the sticks as a comparative screening check, not a substitute for the manufacturer's alignment procedure.** Proper jointer setup includes straightedge/level checks, table adjustments, fence squaring, knife setting, outfeed-table height and final testing; WOOD Magazine does not present winding sticks as a complete alignment procedure [manual, relayed][WS31]. - **Hand position and edge handling:** keep hands and fingers clear of the cutterhead and knife edges while the sticks are placed and read; handle any sharpened bevel edge on the sticks with care. This is general shop practice, not drawn from a named source in this entry. - **Workholding:** set the sticks only on a stable, non-rocking seat; do not steady a rocking stick by hand near a cutter. General practice, not from a named source. - **PPE and the manual's limits:** wear the PPE the machine's manual requires for tool setup and adjustment, and stay within the manual's stated procedures and limits [manual, relayed]. - **Construction hazards are separate.** Making a pair introduces the ordinary hazards of the saws, planes, drills, inlay tools, finishes and metalworking processes used [per the reviewer, not independently re-read]. - **Dropped or swung sticks.** A dropped long stick can injure feet or damage a surface [per the reviewer, not independently re-read]; metal edges can dent work (see *damaging*). - **damaging:** - **To the sticks themselves — seasonal wood movement is the primary documented failure mode.** A named forum poster reports his non-quartersawn wooden pair "moved enough to give me false readings always thinking that one corner was lower," which is why he switched to aluminum angle stock [WS7]. Periodic re-checking (standing the pair together and looking for light leaks) is the documented maintenance response [WS4]. - **Metal winding sticks can mar the workpiece — a named, direct material-choice warning.** Joel Moskowitz states plainly that metal sticks "can easily dig in the wood, causing dents and other problems," and prefers wood partly because it's light enough that an accidental knock causes little damage [WS13]. - **Trusting a pair that has gone out of true corrupts the workpiece downstream, not just the tool's own accuracy.** This follows directly from the re-truing warnings above — a woodworker either over-planes a board that was actually fine, or proceeds to joinery/assembly on a face that is still genuinely twisted. No single source states this workpiece-side consequence as explicitly as the tool-damage side; held as a reasonable inference from directly-sourced material rather than a directly-quoted claim [WS-gap]. - **beginner-trap:** - **Sighting when the sticks rock or do not seat repeatably.** A cupped board can make the sticks see-saw and produce a false twist reading; establish stable reference contacts before trusting the comparison (see *correct use*). Pressure should not be part of the sighting operation. Fine Woodworking's instruction is the source of the stricter remove-cup-first order [WS19, not re-read in this pass]. - **Inconsistent placement.** Sellers names off-center placement as a cause of false readings ("uneven weight... can leave gaps") [WS9][WS11]; the general point is to keep the sticks perpendicular to the work, parallel in plan, consistently oriented and stably seated. - **Reading the sightline in bad or unmanaged light without adjusting which edge faces you.** Highland Woodworking's contrast-management technique (see *correct use*) is a genuinely non-obvious skill a first-time user would not know to apply, and skipping it produces an ambiguous or misread sightline [WS20]. - **Mistaking a plain shop-made pair for scrap and losing it** — a real, named, dated first-person incident (Follansbee, see *human side*), independently corroborated by a second named forum poster reporting the identical loss [WS1][WS7]. This is the direct, sourced reason the contrasting-inlay decoration tradition (see *human side* and *anatomy*) exists as more than pure aesthetics. - **Using an improvised, unmatched pair without confirming both members are actually true** (e.g., a plane sole paired with a ruler, or a level paired with a straightedge) — documented as workable in a pinch but explicitly caveated by its own practitioner-source as less rigorous than a real matched pair [WS15]. - **lineage-misuse:** - **Treating winding sticks and a straightedge as interchangeable.** A straightedge reads straightness along a single line and may reveal twist only through multiple or diagonal checks; winding sticks give the direct, amplified comparison between two cross-sections. Neither is a clean one-way substitute for the other [SE-cross][WS19][per the reviewer, not independently re-read]. - **Substituting a spirit level — a conditional screening substitute, not a visual amplifier.** Named woodworkers describe using a bubble level in place of winding sticks, checking that the bubble sits in the same position at both ends of a span [WS7][WS12]. A calibrated spirit level used in the same orientation at both cross-sections can compare their gravity-referenced slopes and so screen for twist; the difference in slopes is the twist being sought. Limits: vial sensitivity, length, calibration, stable seating and consistent orientation [per the reviewer, not independently re-read]. The first-pass "no relationship" and "category confusion" statements are withdrawn. - **Confusing the tool's core twist-detection identity with its secondary diagonal bar-gauge (squareness) use.** Both are real and sourced (see *correct use* and *matching*), but they are mechanically distinct techniques sharing the same physical object — a heuristic built from this entry should not collapse "winding sticks check twist" and "winding sticks can check square" into a single undifferentiated claim [WS20]. --- ## correct use - **what it's genuinely good at:** revealing twist ("wind") in a board face, a glued-up panel, a bench top, a door or sash frame, or a table's apron/leg assembly — a defect a flat-along-one-line check (a straightedge) shows only indirectly, through multiple or diagonal checks, because a board or assembly can be individually flat or straight at every point checked and still be twisted end to end [WS4][SE-cross]. - **the core mechanic.** Set the two sticks across the work at each end (or at the two reference points that matter — e.g., a tenon cheek and its shoulder), crouch or lower your eye to bring it level with the tops of the sticks, close one eye, and sight across the near stick's top edge to the far stick's top edge; any twist in the surface between them shows up as an apparent misalignment between the two edges, amplified by the distance between the sticks far more than it would be visible by eye on the board's surface alone [WS9][WS20][WS26]. - **check cup separately, and make sure each stick seats repeatably without rocking.** Stable contact is required. Severe or irregular cup can rock the sticks and corrupt a reading, so before trusting the comparison, establish stable reference contacts, use a suitable stilted or contact-point arrangement, or remove enough cup to make the setup stable. Do not use sighting pressure to hold a rocking stick. Total cup removal first is not universally required: Popular Woodworking (read directly) uses one stick as a straightedge to read cup, compares the cup at each end, and then works the twist, and does not say to remove cup first [WS14]. The original's stricter sequence was attributed to Fine Woodworking's Pavlak [WS19]; that article was not re-read in this pass, so treat it as that method's order, not a rule for every setup. - **manage lighting and background deliberately — a real, sourced technique refinement, not folklore.** Highland Woodworking states the rule directly: *"To establish good contrast for maximum visibility, orient one flat side and one beveled edge toward you. If the background is bright, put the light-colored flat side closest to you, so the black bevel beyond will show clearly. Against a dark background, reverse the setup."* [WS20] - **centering aids repeatable placement and symmetric amplification.** Sellers recommends centering (see *human side*) [WS9][WS11]. Wherever the sticks are placed, keep them perpendicular to the work, parallel in plan, consistently oriented, and stably seated [per the reviewer, not independently re-read]; a true, stable stick compared while offset can still read twist if it seats consistently. - **on a jointer or planer, power first.** Disconnect the machine from power, prevent restart, wait for all motion to stop, and follow the model's manual before removing or displacing any guard or working near the cutterhead [manual, relayed]. See *dangerous*. - **also serves as a squareness bar-gauge — a real, genuinely different secondary use, flagged rather than folded silently into the tool's core identity.** Held face-to-face with beveled ends pointing outward, a matched pair of winding sticks can be slid to nest into the corners of a box, carcase, or frame to compare diagonal measurements for square, the same principle as a pair of dedicated diagonal-check sticks [WS20]. This is a legitimate, sourced technique, but it uses the sticks as a length-comparison tool, not a sighting tool — the tool's *core* identity in every other source researched is twist detection; this secondary use is named honestly rather than either suppressed or blurred into the main function. --- ## ✦ matching — for the app's read - **does:** qualitatively reveals relative twist/wind between separated sections of a board face or edge; reveals twist in a glued-up panel or an already-assembled joint (e.g., a tenon cheek checked against its own shoulder) [WS19]; reveals twist in a door, window sash, or a table's apron/leg assembly during dry-fit — Fine Woodworking states the stakes: *"even though a table may have legs of equal length and sit on a level surface, it can still rock and wobble because of twist"* [WS19]. A rocking table can also come from unequal feet, floor irregularity, loose joinery or frame twist; the sticks help diagnose twist but do not identify every cause [per the reviewer, not independently re-read]. Checks a workbench top for twist alongside a straightedge for flatness [WS23]. **Data class, split:** *generic matched sticks* are qualitative twist references; *calibrated or grooved products* (Lee Valley's, via its documented ratio, [WS29]) may estimate magnitude by the manufacturer's method; *jointer or planer table alignment* is a model-specific procedure (straightedge, feeler-gauge, dial-indicator and cutterhead steps from the maker's manual) that winding sticks can only supplement, as a comparative screening check, never as the procedure, and only with the machine disconnected from power [manual, relayed][WS21][WS22][WS31]. Ordinary sticks do not identify which surface is wrong, do not establish straightness along a line, do not set cutterhead height, and give no tolerance without calibrated geometry [per the reviewer, not independently re-read]. Secondarily, a matched pair can be used as a diagonal bar-gauge to check a case or frame for square (see *correct use*, a distinct technique from the core sighting function) [WS20]. - **suits:** rough-stock selection and board-picking before milling — judging cup and twist and marking high corners before a single cut is made [WS14]; post-milling twist verification before glue-up, and again at final glue-up/dry-fit [WS19]; workbench-top flattening, paired with a straightedge [WS23]; casework, door, and sash assembly verification [WS19]; small-scale joinery checks on an individual tenon [WS19]; machine-shop-adjacent use even in a fully power-tool shop — a named source states directly the tool is "just as valuable as I'm working on the jointer, especially when working with extra-long stock that is sensitive to twists" [WS14]; timber-framing-scale twist checks on long stock are more commonly handled with a substitute (a tilt-box/angle-finder) than with full-size winding sticks, per aggregated forum discussion held at lower confidence [WS18][WS25]. - **kit-fit:** - **pairs with:** a **straightedge** — a complementary division of labor per the corpus's own Straightedge entry, similarly stated by Fine Woodworking [SE-cross][WS19]; a **jack or scrub plane** for the corrective cut itself, in the documented workflow of *sight for high corners → mark with chalk → remove material → re-check* [WS14]; for jointer or planer work, the **model-specific alignment method** in the maker's manual, with the sticks as a supplement only. The first-pass feeler-gauge pairing is removed: a feeler gauge does not directly quantify a remote sightline wedge without a defined contact setup [per the reviewer, not independently re-read]. - **substitutes for:** not a clean one-way swap. A single stick can serve as a straightedge for a cup/bow check only after its working edge is verified true [WS14][per the reviewer, not independently re-read]. A straightedge used in several orientations, including diagonals, may reveal symptoms of twist, but is a less direct and less sensitive comparison than the sticks. A calibrated spirit level can screen for twist conditionally (see *lineage-misuse*). Aluminum angle-iron from a hardware store is a commonly cited substitute *material* for building the sticks, not a substitute tool [WS7]. - **cannot replace:** a straightedge, for straightness-along-a-line checks; and the model-specific straightedge, feeler-gauge, dial-indicator and cutterhead procedure for jointer or planer alignment [SE-cross][WS19][manual, relayed]. Winding sticks answer the narrower question of relative wind. - **not-for (project-keyed):** don't reach for winding sticks to check overall flatness of a single face — a board can pass a winding-stick check and still be cupped or bowed along its length; that's the straightedge's job, and the two checks complement each other [WS19]. Don't treat them as a visual amplifier for plumb or level; a spirit level is a different, gravity-referenced instrument (though see *lineage-misuse* for its conditional screening use). Don't use them in place of the manufacturer's alignment procedure on a jointer or planer. **A genuine, honestly-flagged complication:** a matched pair *can* legitimately check squareness via the diagonal bar-gauge technique (see *correct use*), a real secondary use mechanically distinct from the tool's core sighting function. - **access:** the sticks themselves are low-hazard passive references (no blade, no motor, no stored energy), but beginner-safe is not claimed for every use: used on a jointer or planer they put the user near an exposed cutterhead and require power isolation first (see *dangerous*). **Reading** the sightline correctly is also a real, sourced skill with a learning curve: sources describe managing which face/bevel is presented against a light or dark background [WS20], placing the pair repeatably and centered, which Sellers stresses [WS9][WS11], getting stable seating despite cup [WS14][WS19], and (per aggregated, lower-confidence tips) practicing first on a short board [WS-gap]. A first-time user handed a pair cold is likely to misread the sightline without this technique context. - **revival:** the strongest sourced case is that the tool is not obsoleted by power equipment — a named source states plainly it remains "just as valuable" working at the jointer, especially on long stock, because the machine does not check incoming stock twist for you [WS14]; for the machine's own table alignment the maker's procedure governs, not the sticks (see *dangerous*). It is also nearly free — forum consensus is emphatic that any two matched, parallel-edged scraps work, with named posters actively discouraging buying a commercial pair [WS7]. Paul Sellers frames picking the tool up as reviving a fading but once-universal shop practice — *"I don't know of many that rely on winding sticks for detecting twist in boards and billets these days but I use mine often as in days past most woodworkers did"* [WS11] — and the contrasting-inlay decoration tradition (see *human side*) doubles as a real, low-stakes first shop-made-tool project for a beginner: cheap material, a genuine skill payoff, and — per Follansbee's own burned-pair story — a good reason to decorate it so it doesn't get mistaken for kindling. --- ## anatomy - **sighting edge (top edge)** — the working reference edge of each stick, the one read against its partner across the span; Highland Woodworking's technique explicitly manages which face is presented as the sighting edge depending on shop lighting (see *correct use*) [WS20]. - **bevel** — one long edge is commonly beveled to a thin, high-contrast line to sharpen the visual read and, when a single stick is pressed into service as a straightedge, to improve a light-gap test [WS20]. - **taper** — the traditional cross-section tapers from a wider, heavier base (Sellers: extra base weight helps the stick "sit" properly on the work without being nudged out of position) to a narrower, finer sighting edge at the top [WS9][WS4]. - **center-point marker/inlay** — a contrasting dot, rod, or inlay set at the midpoint of each stick so the user can place the pair repeatably and symmetrically on the workpiece; Sellers names centering as important to his reading (see *human side*) [WS9][WS11]. Its value is repeatability, not a proven necessity of the measurement (see *correct use*). - **contrasting sighting inlay** — a light/dark strip inset along the top edge (ebony/maple, ebony/holly, brass/rosewood) purpose-built to make the sightline easy to read against variable shop backgrounds [WS9][WS14]. --- ## variations (living) - **shop-made wooden pair (the dominant tradition)** — hand-planed from quartersawn hardwood (mahogany, beech, cherry all documented), preferred quartersawn specifically because it moves less seasonally and stays accurate longer than flatsawn stock [WS9][WS14][WS2]. Trued by planing both sticks face-to-face or back-to-back until even shavings come off both, then checked for parallelism by standing them together and looking for light leaks between the edges [WS4][WS13]. - **aluminum-angle-stock pair (the Dunbar/Schwarz lineage)** — cross-cut lengths of hardware-store aluminum angle, valued for dimensional stability (aluminum doesn't warp the way wood does) and manufacturing-process accuracy; multiple named forum users report sub-0.004" accuracy over 24" from shop-bought extrusion [WS7][WS8]. - **live current commercial product — Lee Valley/Veritas.** Extruded aluminum, 18" pair, item 50N0101, $46.50 USD (directly fetched, July 2026): satin-black anodized on one side for glare reduction, with machined contrast grooves spaced 1/8" apart on the other side "to help estimate the amount of twist and how much stock to remove," nesting for storage, made in Canada, described by the manufacturer as "Patented" [WS6]. The care-and-use sheet prints U.S. Design Patent D576,850 (a product-design patent, not a concept patent) and documents a product-specific method: count the grooves showing above the near stick, then convert with Ta = Tm × (W / 18), where Ta is actual twist, Tm measured twist and W the board width in inches; it also says to set the sticks square to the board's side [WS29] (read directly). This calibrated estimate belongs to the grooved Lee Valley design, not to every pair. - **retired commercial product — Woodpeckers OneTIME Tool (2012).** Solid CNC-machined aluminum, three lengths (7"/23"/47") plus a full set, three distinct sighting-edge treatments (solid white / red-with-white-end-segments / full-length shiny V-groove), a milled recess on the underside for stability on rough-sawn stock; retired April 9, 2012, now found only in third-party historical-archive listings [WS22][WS27]. - **boutique/decorative pair — Honey Brook Tools (Will Adams).** Currently sold with a brass-rod center-point inlay, referenced and photographed in use by a 2025 Popular Woodworking feature [WS14][WS28]. - **the "stilted" or pegged-foot variant** — a modern maker's own build, patterned after devices he identifies on Roubo Plate 14, uses pegged/doweled "stilt" feet. The page (read directly) says the Plate 14 sticks "are designed to produce a reference edge on the lumber to be planed" and that Roubo's design "looks to enable you to focus on one task at a time", contrasted with ordinary sticks where one is "fighting two dimensions at a time: any cupping as well as any winding" [WS2]. A modern maker's reading, not primary historical proof; the review also describes it as isolating reference contacts on a cupped face. - **laser/digital substitutes — real forum discussion, no confirmed shipped commercial product.** Multiple threads describe mounting a laser or angle-finder to check twist over spans too long to sight conventionally (a technique more associated with timber framing than bench woodworking), but this run found no confirmed, currently-sold "laser winding stick" product — flagged as a theoretical/DIY-experimental category, not an established one [WS18][WS25]. - **no "captured" or magnetic paired product was found** — searched, not located; an honest gap. --- ## trades - **Cabinetmaking / fine furniture / hand-tool woodworking** — the tool's overwhelming home in the sourced record: rough-stock selection, bench-top flattening, casework and door/sash assembly verification [WS9][WS19][WS14]. - **Period/reproduction furniture-making** — Follansbee's and Alexander's own practice, explicitly adopted despite the acknowledged absence of period textual evidence for the technique itself [WS1]. - **Timber framing** — a related but distinct practice at a larger scale; full-size winding sticks are less practical on long timbers, and forum-level discussion suggests digital tilt-boxes/angle-finders are the more common substitute for checking wind on long beams — held at lower confidence, aggregated rather than pinned to one named timber-framing authority [WS18][WS25]. - **Machine-shop-adjacent woodworking** — checking incoming stock for twist before it goes to the jointer or planer [WS14]. For checking jointer/planer table alignment, Woodpeckers' retired product copy says the sticks are "also excellent for checking jointer beds for proper alignment" [WS22]; that is manufacturer marketing, and any such check is a screening supplement done with the machine disconnected from power, not a replacement for the manufacturer's procedure (see *dangerous*) [manual, relayed][WS21][WS31]. --- ## lineage - **ancestors — not found in the sources searched; a research finding, not a documentary boundary.** Peter Follansbee, a specialist in 17th-century joined furniture who works directly from period sources with Jennie Alexander, wrote: *"The winding sticks are quite helpful for checking that the board is flat; but Alexander & I have never found period evidence for them however. Moxon does not mention them, nor Randle Holme. We use them anyway."* [WS1] In the same post he adds that he will later "dig out the only early engraving we have seen that shows a pair of sort-of winding sticks in use" [WS1] (read directly in this pass). So the accurate statement is: Follansbee and Alexander reported finding no mention in Moxon's *Mechanick Exercises* or Randle Holme's *Academy of Armory*, while Follansbee also noted an early engraving of a "sort-of" pair that still needs identifying. Preserved as strong named-practitioner research evidence, not as proof that period ancestors or period use are undocumented across the historical record. - **Roubo, Plate 14 — not mapped figure by figure here.** Modern sources identify both winding-stick-like battens and a *pied de biche* among different devices on Roubo's *L'Art du Menuisier* (1769–74) Plate 14: a modern maker states his pair is patterned after the devices on that plate [WS2], and a Lost Art Press comment thread identifies one figure on the plate as a *pied de biche*, a notched block used with a holdfast to hold work [WS3]. A plate can carry several numbered objects, so these statements are not inherently in conflict. Lost Art Press's own table of contents for *Roubo on Furniture* lists "Make Roubo's 'Winding Sticks'" (page 54) [WS30] (read directly in this pass), which is positive evidence that the publisher recognizes a Roubo winding-stick form. The first-pass framing of a "real, unresolved contradiction" is withdrawn. This entry has not inspected Plate 14 or the translated text, so it cites no figure numbers and claims no more than the above. - **possible mid-19th and early-20th century print descriptions — unverified leads.** Wikipedia/HandWiki attribute the traditional 16"–30" length range and taper dimensions to Charles Holtzapffel, *Turning and Mechanical Manipulation*, Vol. 2 (1856), p. 500, and George Ellis, *Modern Practical Joinery* (1902), p. 51 [WS4]. This run did not verify those pages in the original editions, so they remain leads, not confirmed earliest descriptions; any "earliest" statement is bounded by the searches made. - **no confirmed connection to a non-woodworking ancestor.** This run searched directly for a lineage tie to shipbuilding "in wind" keel-checking or timber-framing/masonry plumb-and-level practice and found nothing credible — an honest gap, not filled with a plausible-sounding invented connection. - **no patent for the traditional concept located; a design patent exists for Lee Valley's product.** DATAMP and Google Patents searches returned nothing for a woodworking winding-stick concept patent [WS5]. Lee Valley's care-and-use sheet for item 50N01.01 prints "U.S. Des. Pat. No. D576,850" [WS29] (read directly in this pass). That is a design patent on the commercial product's form, not a patent on the traditional winding-stick concept. The separate finding that no foundational patent for the concept was located is unchanged. - **a real, named, dated (2010) transmission-of-technique lineage — the strongest single provenance chain in this entry.** Christopher Schwarz's aluminum-angle-stock winding sticks, which he popularized through *The Anarchist's Tool Chest* and a widely-circulated Popular Woodworking piece, are directly credited by Schwarz himself, posting in his own words on a public forum: *"I got the idea from Michael Dunbar at The Windsor Institute. Aluminum extrusions are very accurate — it's a result of the manufacturing process."* [WS7][WS8] This is a clean, named, dated (2010) teacher-to-teacher transmission of a specific technique variant, independently traceable through Schwarz's own subsequent publications. - **contemporaries — the corpus's own siblings that get mistaken for it:** - **[[Straightedge]]** — the tool's closest sibling. That entry's framing: "Straightedges do not indicate twist... winding sticks are a pair of narrow boards with parallel edges that allow you to determine if a board, joint, or assembly is—or is not—free of twist" [SE-cross][WS4]. Stated more carefully here: winding sticks are the direct, sensitive check for relative wind between separated sections; a straightedge is primarily for straightness along a line and may reveal twist only indirectly, through multiple or diagonal checks. A single stick can serve as a straightedge only after its working edge is verified true; matching parallel edges alone do not prove straightness [per the reviewer, not independently re-read]. Fine Woodworking's Bill Pavlak carries a similar claim in his own words [WS19]. - **Spirit level** — a different reference (gravity versus a sightline between two edges), but a calibrated level read in the same orientation at two cross-sections can compare their slopes and so screen for twist; see *lineage-misuse* below. --- ## history - **the technique's actual age is not established by the sources searched — an honest gap, not an invented "ancient" origin.** No dated origin point was located; Follansbee and Alexander report no mention in Moxon or Randle Holme, and he notes an early engraving of a "sort-of" pair that is not yet identified [WS1]; Wikipedia/HandWiki cite Holtzapffel (1856) and Ellis (1902) as print descriptions, unverified here [WS4]. General claims that the technique dates to "medieval carpenters" appear in tertiary sources without their own citation to a primary document; this entry does not repeat that claim as settled fact. - **the traditional dimensional convention, as Wikipedia/HandWiki attribute it to Holtzapffel (1856) and Ellis (1902), neither checked here:** 16"–30" long, roughly 1¾" tall, tapering in height from ⅜" at the base down to ⅛" at the sighting edge [WS4]. - **no foundational patent, but a real, dated commercial-product history exists on the modern end.** Woodpeckers ran solid-aluminum winding sticks as a limited "OneTIME Tool" release in three lengths (7", 23", 47", plus a full set), **retired April 9, 2012**, with the maker's own retirement notice stating "If there's enough demand, we may re-run some of these tools" [WS22] — confirmed still catalogued only as a historical archive line at a third-party retailer today, not a current standing SKU [WS27]. Lee Valley/Veritas, by contrast, sells a live, current pair (item 50N0101, $46.50 USD, directly fetched July 2026) [WS6]. --- ## ✦ human side - **Peter Follansbee — the entry's named source for both the "no period evidence" finding and a real, dated first-person technique-and-loss story.** Beyond the negative-evidence finding above, Follansbee also uses winding sticks to check that mortise-and-tenon joint faces sit in the same plane, not just for raw stock prep [WS1]. Replying to a reader who asked him to rebuild a pair, Follansbee wrote: *"I made some out of 1/4rd oak, but they got shuffled out of the shop. They looked too much like everything else, so I think they got burned."* [WS1] A second, independent, named forum poster reports the identical complaint — *"I'd like some permanent ones that will not be mistaken for scrap, as happened with one of my wood ones"* [WS7] — a real, corroborated human-side finding: an unadorned wooden pair looks enough like an offcut to get burned in the shop stove, which is part of why the contrasting-inlay decoration tradition below exists. - **Christopher Schwarz and Michael Dunbar — the named teacher-to-teacher lineage.** See *lineage* above [WS7][WS8]. - **Paul Sellers — the most extensively documented living-practitioner source for construction and technique.** Builds winding sticks by hand from mahogany (20mm × 32mm × 406mm / ¾" × 1¼" × 16"), with ebony and curly-maple inlays for sighting contrast [WS9][WS10]. On centering he writes that *"it's very important the winding sticks are centred on the boards when being checked"* and that uneven placement can give a false reading [WS11] (read directly); this is his method and his explanation, kept here as named practitioner evidence, not as an established universal physical requirement. In the 2011 post he calls the practice "rack o' th' eye", says shops relied on it for planing accuracy, says "every shop had large and small pairs", and says a pair twice the stock's width "exaggerated the twist by twice as much" [WS11] (read directly). These are Sellers's statements; they are not independent evidence that the phrase or the "every shop" claim was universal period usage. He frames the tool as a fading tradition worth reviving: *"I don't know of many that rely on winding sticks for detecting twist in boards and billets these days but I use mine often as in days past most woodworkers did... a slight twist on one rail or stile translates into a twisted door, wasted wood and lost time"* [WS11] - **A real, named, dated (2012) forum debate over whether the tool is even necessary — a genuine, kept-not-resolved disagreement.** Guest writer John Leko argued on Lost Art Press's own blog for a straightedge-only method, without winding sticks; multiple named commenters pushed back directly, with one stating the precise mechanical reason winding sticks catch what a straightedge alone cannot: *"Winding sticks check primarily for twist; a board with equal cup at each end could check out perfectly, provided the cupped board was not twisted also... It too would check out perfectly with winding sticks."* [WS12] Preserved here as a genuine, unresolved practitioner disagreement, not flattened into one verdict. - **Joel Moskowitz (Tools for Working Wood)** — builds winding sticks with removable floating-tenon construction specifically so the sticks can be re-planed and re-trued as they move over time, and states a direct material-safety reason for preferring wood over metal: metal sticks "can easily dig in the wood, causing dents and other problems," while wood sticks are light enough that a knock causes little damage [WS13]. - **The contrasting-inlay tradition (holly, ebony, boxwood, brass) — real and widespread, no single named originator.** Sellers uses ebony/maple and ebony/holly; Joel Moskowitz inlays a boxwood "target" specifically to force the eye to compare the same reference point on repeat checks [WS13]; a 2025 Popular Woodworking feature documents both a brass center-rod marker and separate contrasting top-edge inlays as distinct, purpose-built conventions, and references a boutique maker, Will Adams of Honey Brook Tools, who currently sells decorative pairs built on this principle [WS14][WS28]. --- ## ✦ proof of existence - **no dated origin point was located from the primary record in this run.** Wikipedia/HandWiki cite Holtzapffel (1856) and Ellis (1902) as print descriptions; neither original was checked here, so these are leads, not confirmed earliest descriptions [WS4]. Follansbee also mentions an early engraving of a "sort-of" pair that is not yet identified [WS1]. - **no museum/collection accession record for a specific dated antique winding-stick pair was located** at the Smithsonian, Mercer Museum, V&A, or Winterthur. This run confirmed the Mercer Museum's general scope (roughly 50,000 pre-1850 American trade/craft objects, built from Henry Chapman Mercer's fieldwork, with his 1929 catalog *Ancient Carpenters' Tools* the standard period reference for exactly this class of shop-made joiner's tool) and Winterthur's general scope (90,000+ objects), but could not confirm — nor rule out — whether winding sticks specifically appear in either collection or in Mercer's own catalog without a direct search of the primary catalog text, which was not completed this run [WS16][WS17]. **A genuine, honestly-flagged gap**, not papered over with the adjacent collection-scope material. - **no foundational patent for the concept was located**; Lee Valley's current product carries U.S. Design Patent D576,850, a product-design patent printed on its care-and-use sheet [WS5][WS6][WS29]. - **a real, dated, verifiable modern commercial-product history exists in place of deep antiquity.** Woodpeckers' OneTIME Tool release and its exact retirement date (April 9, 2012) is directly documented [WS22]; Lee Valley/Veritas's current, live product (item 50N0101, $46.50 USD) was directly fetched July 2026 [WS6]. This is a thinner form of "proof of existence" than a dated antique object or a foundational patent, but it is genuine, dated, and directly verified rather than inferred. --- ## references | Tag | Source | Kind | |---|---|---| | WS1 | Peter Follansbee, "joined stool seat board, pt 1," pfollansbee.wordpress.com, 2010-01-24, https://pfollansbee.wordpress.com/2010/01/24/joined-stool-seat-board-pt-1/ (incl. comment-thread exchange with reader Bryan MacIntyre) | named-maker blog + comment thread | | WS2 | Rose-Hulman Institute of Technology (W. Wollowski), "Roubo Winding Sticks," https://www.rose-hulman.edu/~wollowsk/wood/windingSticks.html | named-maker technical page | | WS3 | Lost Art Press, "The Dawn of the 'Dürer Stick,'" 2013-11-29, comment thread, https://blog.lostartpress.com/2013/11/29/the-dawn-of-the-durer-stick/ | blog + comment thread | | WS4 | Wikipedia, "Winding stick," https://en.wikipedia.org/wiki/Winding_stick; mirrored at HandWiki, https://handwiki.org/wiki/Engineering:Winding_stick | encyclopedia | | WS5 | DATAMP (Directory of American Tool and Machinery Patents) and Google Patents, direct searches — no winding-stick-specific patent located | patent search, negative result | | WS6 | Lee Valley, "Winding Sticks, pair" (item 50N0101), directly fetched July 2026, https://www.leevalley.com/en-us/shop/tools/hand-tools/planes/maintenance-and-accessories/53276-lee-valley-winding-sticks | product (directly fetched) | | WS7 | Sawmill Creek Woodworking Community, "Chris Schwarz's winding sticks," 2010-07-27, https://sawmillcreek.org/threads/chris-schwarzs-winding-sticks.145031/ (Christopher Schwarz, Zach England, Tony Shea, Mark Dorman) | forum, incl. named-maker post | | WS8 | Popular Woodworking, Christopher Schwarz blog, "Winding Sticks with Better Visibility," https://www.popularwoodworking.com/woodworking-blogs/chris-schwarz-blog/winding-sticks-with-better-visibility | named-maker blog | | WS9 | Paul Sellers, "Making Winding Sticks by Hand – Part I," 2014-05, https://paulsellers.com/2014/05/making-winding-sticks-by-hand/ | named-maker blog | | WS10 | Paul Sellers, "Making Winding Sticks by Hand – Part II," https://paulsellers.com/2014/05/making-winding-sticks-by-hand-part-ii/ | named-maker blog | | WS11 | Paul Sellers, "Winding sticks for guaranteed flatness — and more beyond," 2011-11-17 (read directly 2026-10-16), https://paulsellers.com/2011/11/winding-sticks-for-guaranteed-flatness-and-more-beyond/ | named-maker blog | | WS12 | Lost Art Press, "Are Winding Sticks Necessary?," 2012-09-13, https://blog.lostartpress.com/2012/09/13/are-winding-sticks-necessary/ (guest post by John Leko, plus named commenters) | blog + comment thread | | WS13 | Tools for Working Wood (Joel Moskowitz), "Winding Sticks," 2011-01, https://toolsforworkingwood.com/store/blog/265 | named-maker blog | | WS14 | Popular Woodworking, Logan Wittmer, "Winding Sticks," 2025-07-24, https://www.popularwoodworking.com/techniques/winding-sticks/ | trade publication | | WS15 | Literary Workshop Blog, comment thread, 2014-02-03, https://literaryworkshop.wordpress.com/2014/02/03/winding-sticks-we-dont-need-no-stinkin-winding-sticks/ | blog + comment thread | | WS16 | Mercer Museum, collection overview, https://www.mercermuseum.org/collections/mercer-museum/; Henry C. Mercer, *Ancient Carpenters' Tools* (1929), Internet Archive, https://archive.org/details/ancientcarpenter0000merc | museum collection (scope only, not independently searched to primary-catalog level) | | WS17 | Winterthur Museum, online collection, https://museumcollection.winterthur.org/ | museum collection (scope only) | | WS18 | LumberJocks, "Laser winding stick?," https://www.lumberjocks.com/threads/laser-winding-stick.294041/ | forum (thread title only, full content not fetched) | | WS19 | Fine Woodworking, Bill Pavlak, "Shopmade Winding Sticks Guarantee Accuracy," FWW #276, Jul/Aug 2019, https://www.finewoodworking.com/project-guides/shop-projects/handwork-winding-sticks-guarantee-accuracy | trade publication | | WS20 | Highland Woodworking, "What Are Winding Sticks," https://www.highlandwoodworking.com/pages/custom-what-are-winding-sticks | trade reference | | WS21 | Sawmill Creek Woodworking Community, "Jointer table coplanarity tolerance," https://sawmillcreek.org/threads/jointer-table-coplanarity-tolerance.295320/ | forum | | WS22 | Woodpeckers, "OneTIME Tool: Winding Sticks (2012)," retired product page, directly fetched, https://www.woodpeck.com/onetime-tool-winding-sticks-2012.html | product (directly fetched, retired) | | WS23 | Wood & Shop, "How To Make Winding Sticks For Woodworking," https://woodandshop.com/making-winding-sticks-for-flattening-workbench-tops/ | trade blog | | WS24 | Wood & Shop, "How to Use Winding Sticks," https://woodandshop.com/how-to-use-winding-sticks-woodworking/ | trade blog | | WS25 | LumberJocks, "Alternatives to Winding Sticks - Please Help Me," https://www.lumberjocks.com/threads/alternatives-to-winding-sticks-please-help-me.358077/ | forum | | WS26 | Australian Wood Review, "How to make and use winding sticks," https://www.woodreview.com.au/how-to/how-to-make-and-use-winding-sticks | trade publication | | WS27 | Incremental Tools, "Woodpeckers One Time Tools" archive category, https://www.incrementaltools.com/category_s/307.htm | retailer (third-party archive confirmation) | | WS28 | Honey Brook Tools, winding sticks product page, https://honeybrooktools.com/products/winding-sticks — referenced via Popular Woodworking 2025 [WS14] | product | | WS29 | Lee Valley, Winding Sticks care-and-use sheet (item 50N01.01), https://assets.leevalley.com/Original/10092/53276-lee-valley-winding-sticks-c-01-e.pdf — U.S. Des. Pat. No. D576,850; groove and ratio method; sticks set square to the board's side (read directly 2026-10-16) | manufacturer instruction sheet | | WS30 | Lost Art Press, "Table of Contents for Roubo on Furniture," 2016-12-12, https://blog.lostartpress.com/2016/12/12/table-of-contents-for-roubo-on-furniture/ — lists "Make Roubo's 'Winding Sticks'" (read directly 2026-10-16) | publisher page | | WS31 | WOOD Magazine, "Tuning up your jointer," https://www.woodmagazine.com/tuning-up-your-jointer — unplug before table alignment; alignment is a multi-step procedure. NOT read in this pass (site blocked); carried from the review, `[manual, relayed]` | trade publication (relayed) | | WS-gap | Claims searched for but not sourced this run ("practice on a short board first" tip, workpiece-side damage consequence of trusting an out-of-true pair); the feeler-gauge pairing is removed. Flagged inline at point of use | honest gap marker | | SE-cross | [[Straightedge]] (this corpus), own citation of winding sticks as its single most important paired sibling and the "cannot replace" claim | corpus cross-reference | | JN-cross | [[Jointer Plane]] (this corpus), own citation of winding sticks as part of final flatness verification | corpus cross-reference | | J-cross | [[Jack Plane]] (this corpus), own citation of winding sticks as the check during the diagonal-traverse rough-flattening stroke | corpus cross-reference | --- ## The reviewer's corrections (12) - `BLOCKER` — 1. — Exact claim: “checks jointer infeed/outfeed table coplanarity”; “genuinely beginner-safe on the injury axis”; and the dangerous category is “Honestly and fully empty.” - `SHOULD-FIX` — 2. — Exact claim: “the Roubo question — a real, unresolved contradiction in the secondary literature” between Plate 14 winding sticks and figure 17's *pied de biche*. - `SHOULD-FIX` — 3. — Exact claim: “ancestors — genuinely undocumented; the entry's central, most load-bearing finding” and the history's broader inference from Follansbee. - `SHOULD-FIX` — 4. — Exact claim: “the earliest dated print descriptions found are” Holtzapffel (1856) and Ellis (1902), later restated as “the earliest confirmed print descriptions.” - `SHOULD-FIX` — 5. — Exact claim: “remove cup first — a sequencing rule, not optional” because cup makes the sticks “see-saw/rock under sighting pressure.” - `SHOULD-FIX` — 6. — Exact claim: “a straightedge alone cannot detect twist” and “the reverse substitution works one direction only.” - `SHOULD-FIX` — 7. — Exact claim: “off-center placement introduces uneven weighting that can lift one end” and is a general beginner trap. - `SHOULD-FIX` — 8. — Exact claim: Using a spirit level as a substitute is “a genuine category confusion” with “no relationship” to winding-stick measurement. - `SHOULD-FIX` — 9. — Exact claim: The generic pair “detects” machine-table coplanarity and a feeler gauge can quantify its sighting result “in principle.” - `MINOR` — 10. — Exact claim: Lee Valley's patent number “could not independently [be] locate[d] or confirm[ed].” - `MINOR` — 11. — Exact claim: “rack o' th' eye” is an old or historical name for the practice, and “every shop” once had pairs. - `MINOR` — 12. — Exact claim: Confidence is “MEDIUM-HIGH.”