# Taper Reamer (Chairmaking)

Hewn Tool Library · https://hewn.build/tools/taper-reamer-chairmaking

Corrected: An independent reviewer read this entry and found corrections. They have been applied to the text, and the reviewer re-checked the correction that mattered most for safety and found it done; the others have not been re-checked yet. The list at the end is the record of what changed.

Cite as: "Taper Reamer (Chairmaking)." Hewn Tool Library, hewn.build/tools/taper-reamer-chairmaking. Reviewed 2026-09-19.

---

## Identity

- **Core definition.** A conical cutting tool that enlarges an existing straight-bored hole (a chair seat's leg or arm-stump mortise, for example) into a controlled taper, for a tenon made with a verified matching cutter or method. It is not ordinarily the tool that starts an undrilled mortise. Drive method is model-specific: some reamers are for a hand brace only, some are designed for an electric drill (see Variations). — Bizzarri, "Using a Chairmaking Reamer" and "Reamers"; Veritas and Lee Valley product pages, read directly.
- **It cuts the female half of the joint; the tenon cutter cuts the male half.** A tapered tenon cutter forms the tenon; the reamer forms the socket. They are not interchangeable, and they are bought and used as a matched system: Bizzarri's tenon cutters "cut a six-degree tapered tenon to match the taper of my reamers" (read); Veritas Standard reamers' "included angle of 12.8° ... matches the tenons made with the Veritas Tapered Tenon Cutters" (read). A mismatch in taper between reamer and tenon gives a loose or over-tight joint (Bizzarri's angle material; Sawmill Creek "Tapered Reamers" thread, search-summarized).
- **"Reamer" covers materially different constructions.** Adjustable wooden-bodied cutters (Starr/Bizzarri, Manney), an adjustable cast-steel-bodied brace tool (Veritas Pro), and one-piece steel drill-driven forms (Veritas Standard). Their operating instructions are not interchangeable.
- **Maker systems, recorded in each maker's own words.** These are maker systems, not standards issued by any standards body, and compatibility is never inferred from the headline number alone.
  - **Veritas** (Pro and Standard): "Body has included 12.8° angle" (Pro page); "The included angle of 12.8° on both reamer bodies" (Standard page). Convention: included angle.
  - **Elia Bizzarri:** reams "to a six-degree taper," and the blade "taper[s] at a 6 degree included angle" (Reamers page). His compound-angle method subtracts half the taper, consistent with an included-angle figure. Convention: included angle, per his blade spec.
  - **Tim Manney:** "with a 6 degree taper" (read); the page does not say whether that is included or per side. Convention: not established.
  - On the makers' own stated conventions, the Veritas and Bizzarri systems differ (12.8° vs. 6° included). Whether Manney's tools match Bizzarri's is not established from the label; verify reamer, tenon cutter, template and setup reference as one matched system.
- **A thin patent and institutional record in the sources checked.** No historical US patent specific to a chairmaking taper reamer was located, and the Veritas Pro listing carries no patent number. This is a search result, not proof of absence; no full DATAMP class search was run. Schwarz: reamers "show up in the historical record as a shop-made tool or something manufactured by a blacksmith or other metalworker. But they aren't terribly common." Bizzarri: "18th Century reamers were blacksmith-made – they are sometimes available from antique dealers or on Ebay" (Samuel Wing Tool List, read).

## How NOT to use it (the heaviest section)

**not-for**
- **Not for cylindrical mortise-and-tenon work.** A design without a taper needs no reamer (Schwarz's historical-default method).
- **Not a substitute for its matched tenon cutter, or vice versa.**
- **Not a machinist's reamer.**
- **Not in a power drill if the maker says brace only.** Veritas Pro: "built for a traditional hand brace only."

**dangerous (injures the user)**
- **The hazards come from the mechanism.** A taper reamer has a sharp exposed cutting edge; hand-brace use can bind and transmit torque to the user's hands and body; drill-driven models add powered rotation, entanglement, torque reaction, loss of control and a workpiece that can spin. Blade adjustment and sharpening expose the edge directly.
- **Workholding.** Secure the seat or workpiece against rotation and movement before reaming, without distorting it. Stop if the workpiece loosens.
- **Drive.** Use only the drive and adapter documented for that exact model; follow the drill manufacturer's torque-reaction precautions on powered models. Brace yourself in a stable stance and start and stop under control.
- **Inspect first.** Check the reamer body, shank, blade, set screws, brace or drill, chuck and any adapter before use. Do not use a cracked body or a loose blade.
- **Power off for hands-on work.** Disconnect or remove the battery from a drill before clearing chips, adjusting the blade, inspecting or changing tools.
- **Edge handling.** Treat sharpening and blade adjustment as exposed-edge work; keep fingers off the edge and use the maker's method (Veritas Standard: hone only the inner surface of the cutting edge).
- **Body and clothing.** Wear eye protection. Keep hands, loose clothing, hair and jewelry clear of the cutter and rotating parts.
- **Stop conditions.** Stop immediately for binding, a grab, abnormal chatter, heat, a loosening workpiece or loss of alignment, and find the cause before continuing.
- **Heat.** Bizzarri's fix for a loose blade is to heat the reamer, held in a vise, with a heat gun "until it's too hot to touch," then let it cool; treat the hot tool as a burn hazard.
- *Research note, kept separate from the hazard class:* no tool-specific incident source was located.

**damaging (ruins the tool or the work)**
- **★ Overreaming.** Schwarz: "People ream for way too long, which burnishes the hole and cooks the reamer." Reaming past a tight test fit oversizes the mortise, glazes the surface and heats and dulls the blade.
- **Forcing a wrongly set blade.** On Bizzarri's adjustable reamer, ignoring chatter and forcing the cut risks tearout and wear; reset the blade as he describes.
- **Wrong honing.** On the Veritas Standard, honing the outer surface changes the reamer's geometry; hone only the inner surface.
- **Uncontrolled angle correction.** Using the taper to pull a mis-bored hole far off its axis can leave an off-axis, weakened, oversized or breakthrough-prone mortise; any correction is limited, planned material removal.

**beginner-trap (looks fine until it isn't)**
- **★ Reaming straight to full depth without progressive test-fitting.** Inferred from converging evidence (Schwarz's overreaming warning, Galbert's late reaming, Bizzarri's progressive approach); no source uses the phrase "test block" or "witness mark" for the reamer, so this is Haft's inference, not quoted doctrine.
- **Assuming any reamer fits any tenon cutter because both say "taper."** Veritas (12.8° included) and Bizzarri (6° included) differ by their makers' own figures; Manney's convention is unstated. Verify the system.
- **Applying one reamer's troubleshooting or drive to another.** Bizzarri's squeak/chatter blade resets do not apply to a one-piece reamer; a brace-only reamer does not go in a drill.

**lineage-misuse (treating it like an ancestor, descendant, or rival)**
- **★ Treating this reamer like a machinist's reamer.** Different trade, material, geometry and feed discipline.
- **Treating the reamer and its tenon cutter as one interchangeable tool.** They cut opposite halves of the joint and are frequently confused by name (see [[Dowel & Tenon Cutter (Hollow Auger)]]).
- **Treating a matched taper as a self-locking, glue-optional joint.** No source here documents an engineered glue-free design; follow the chair design.

## Correct use

**Genuinely good at:** enlarging an existing pilot hole into a controlled taper that a tenon from the matching system seats into with broad contact and controlled seating, the mortise-side half of a chair joint whose tenon is cut by a matching [[Dowel & Tenon Cutter (Hollow Auger)|tenon cutter]].

**Treat reamer, tenon cutter, angle convention, pilot and drive as one documented system.** Work from the chair plan and the exact reamer's instructions.

- **Hold the work.** Secure the seat or workpiece against rotation and movement without distorting it; Bizzarri clamps the seat horizontally on the bench.
- **Pilot.** Bore the pilot specified by the joint plan and the reamer's instructions, within that model's stated capacity. (Schwarz's example: "the smallest size of the overall joint – typically 5/8”," with his 12° Lee Valley reamer.)
- **Drive.** Use only the drive the maker documents for that exact model. Veritas Pro: hand brace only. Veritas Standard: electric drill, and Lee Valley recommends "a high-torque, low-speed drill at about 500 rpm with a minimum 3/8" chuck," fed slowly, especially in softwood (read); or a brace with an adapter. Follow the drill manufacturer's manual as well. Do not carry one practitioner's drill setting (Schwarz's "low speed and maximum torque") onto another reamer.
- **Direction.** Set and check the angle against the plan's reference lines. Bizzarri's method (Human Side) is his and Buchanan's sighting method for his reamer: the bevel square at the resultant angle minus half the taper against the tapered body, or the full resultant angle against the cylindrical section.
- **Cut in small increments.** Bizzarri: "remove the reamer from the hole and remove the shavings from in front of the blade every few rotations."
- **Reading the tool, by design.** *Bizzarri's troubleshooting for his adjustable reamer:* squeaking means clear the chips or set the blade more aggressively; "If the reamer grabs and chatters, set it less aggressively" — retract until it will not cut, then advance until the squeaking stops and it cuts smoothly. For any other reamer, a squeak, chatter or grab means stop, clear chips, inspect the setup and follow that maker's instructions; one-piece reamers have no blade-depth adjustment.
- **Check fit and depth before full depth.** Test against the matched tenon (or the maker's gauge) and stop once the seat is right. Continuing to ream past that point overreams (Schwarz, above).
- **Retention follows the design.** A well-made taper gives broad contact and controlled seating; it does not replace the chair design's or instructor's requirements for glue, wedges, shoulders, moisture condition and assembly.

## Matching (the workbench's first read)

- **Does:** enlarges an existing bored mortise into a controlled taper matched to a tenon from the same verified system.
- **Record as separate fields:** maker, model, working range, angle and its convention (included / per side / unstated), cutter construction, shank, documented drive, matching tenon-cutter family.
- **Suits:** Windsor seat leg and arm-stump mortises and other joints the chair design specifies as tapered. Not every chair mortise, post-and-rung joint or stool leg joint is tapered.
- **Kit-fit — pairs with:** the matching tapered tenon cutter from the same system; a bevel square or gauge and try-square for sighting; the pilot bit the plan and reamer specify; the documented drive (a two-jaw brace for the Veritas Pro; a low-speed high-torque drill for the Veritas Standard); clamps to hold the seat.
- **Substitutes for:** nothing else in the corpus does this specific job.
- **Cannot substitute for:** a tenon cutter; a machinist's or machine-spindle reamer.
- **Not-for (project-keyed):** cylindrical joinery, which needs a bored hole and no reamer; mixing makers' reamers and tenon cutters without verifying the system; inferring compatibility from "6°," "12.8°," appearance or nominal diameter alone; a powered drive on a model documented for a brace only.
- **A one-off tapered joint:** a tapered-tenon design requires a compatible tapered mortise. Borrow or buy the matched reamer, use a documented alternative method that produces the same taper, or redesign and validate the joint as cylindrical. A straight bored hole is a different joint, not a shortcut.
- **Negative matches:** metalworking machine reamers, plumbing deburring reamers, bridge-pin reamers, countersinks, cylindrical hole enlargers, tapered tenon cutters.
- **Access:** a beginner can produce a workable joint, but the tool rewards patience. The main trap is reaming too far, too fast. Overreaming mainly ruins joint geometry; the conditions that cause it (loss of directional control, excessive force, binding, a loose workpiece, a powered reamer turning after control is lost) are injury hazards as well as accuracy ones.
- **Revival:** in current use and sale (Bizzarri, Manney, Veritas/Lee Valley).

## Anatomy

- **Body.** Riven hickory (Starr/Bizzarri); dense tropical hardwood such as purpleheart, bubinga or jatoba (Manney); cast steel alloy with a separate blade (Veritas Pro); one piece of high-carbon steel (Veritas Standard: "Machined from a single piece of high-carbon steel"). The body's taper is the tool's defining spec, recorded with its angle convention.
- **Blade.** A spring-steel blade through a slot, depth set by a set screw (Bizzarri); a separate spring-steel blade (Veritas Pro); no separate blade, the cutting edge is ground on the one-piece body (Veritas Standard: "Hone only the inner surface of the cutting edge with a slip stone or diamond hone"). All are sharp exposed edges.
- **Adjustment.** A set screw controlling blade projection on adjustable designs (Bizzarri; Veritas Pro). One-piece reamers have no comparable blade-depth adjustment.
- **Shank / drive.** Veritas Pro: "tapered square shank for use in two-jaw hand brace." Veritas Standard: "A 5/16" hex shank chucks straight into an electric drill, or into a traditional brace with an adapter." Bizzarri and Manney: drive not stated on their pages.

## Variations (living)

| Variant | Angle (maker's convention) | Construction | Documented drive | Working range | Source |
|---|---|---|---|---|---|
| Starr/Bizzarri-lineage reamer | 6° included | Riven hickory body, slotted spring-steel blade, set screw | Not stated on maker pages | Blade 3/8"–1 1/4" | handtoolwoodworking.com/reamers, read |
| Tim Manney reamer | "6 degree taper" (included vs. per side not stated) | Dense tropical hardwood body | Not stated | Holes 1/2"–1 1/4"; $305 | timmanney.com/work/reamers, read |
| Veritas Pro Taper Reamer | 12.8° included | Cast steel alloy body, separate spring-steel blade | **Hand brace only** ("built for a traditional hand brace only") | Page as read this pass: existing holes 7/16" to 13/16"; Run 615 recorded 7/16"–1 3/16"; confirm against the current listing | veritastools.ca, read |
| Veritas Standard Taper Reamers (Small, Large) | 12.8° included | One-piece high-carbon steel | **Electric drill**; brace only with an adapter | Small 3/16"–3/4"; Large 3/16"–1 3/16" | leevalley.com, read |
| Shop-made reamer (purchased blade, self-built body) | Per blade | Bizzarri sells raw bodies and blades | Per builder | Per blade | handtoolwoodworking.com/reamers |
| Machinist's straight/parallel reamer (metalworking, NOT this tool) | — | Finishes a bored metal hole to constant size | — | — | general reference, naming collision only |

## Trades (where it appears)

**Chairmaking (Windsor and ladder-back/post-and-rung) is the tool's living home** in the sources checked: Bizzarri, Buchanan, Galbert, Alexander and Schwarz all work in it. No wheelwright, lutherie or other cross-trade use was located for this tool; that is an open question, not a documented absence.

## Lineage

- **The tool class predates the current wooden pattern.** Bizzarri describes 18th-century reamers as blacksmith-made (above). No directly relevant patent or museum accession was located in the sources checked.
- **The modern wooden pattern in this teaching lineage: Richard Starr.** Bizzarri credits Richard Starr with developing the modern wooden six-degree reamer pattern used in this teaching lineage ("Developed by Richard Starr," Reamers page, read). Peter Galbert's blog ("The Reamers are Here!", search-summarized) corroborates the credit. Per these sources, the design is a riven hickory body with a saw-steel blade slid through a slot in a solid cone, reaming to a 6° taper, intended to avoid elliptical (out-of-round) reaming. Peter Follansbee's Substack ("A Visit with Rich Starr," free preview only) corroborates Starr's biography and his mid-1990s work with Jennie Alexander on her chairmaking video, where, per that source, the 6° angle was reached with input from an unnamed "old-time craftsman." Held at MEDIUM: two practitioner sources, one partially read. Starr is not the inventor of taper reamers generally.
- **Galbert and Manney later made their own adjustable commercial versions** (chairtools.blogspot.com, search-synthesis, MEDIUM).
- **Tapered joints were not the historical default.** Schwarz: most chair mortise-and-tenon joinery was historically cylindrical, "because you need only simple tools: a brace and bit to make the mortise, and a handplane to make the tenon." This sits beside the unresolved three-way disagreement [[Dowel & Tenon Cutter (Hollow Auger)]] records (folk "self-tightening" claim vs. Bizzarri's dissent vs. Schwarz's error-tolerance argument).
- **Naming collision.** "Reamer" is also a metalworking term for a tool that finishes a bored hole to a precise constant diameter, and tapered machinist's reamers exist for machine-spindle tapers: a different trade sharing the word. (General reference: Wikipedia "Reamer"/"Tapered reamer"; retailer material from WayKen, Travers Tool Co., Sundi/Kakele Tools; MEDIUM, used only to establish the collision.)

## History (Petroski "form follows failure" lens)

- **Several separable problems, not one.** The corpus carries three live, unresolved rationales for tapered joinery: a folk-physics "self-tightens under load" claim; Bizzarri's dissent ("I don't agree that tapered joints get tighter from the weight of the sitter... make a joint that will not fail, because it is tight to begin with"); and Schwarz's error-tolerance argument, that reaming lets an assembler correct some boring-angle error a fixed cylindrical hole cannot. How much correction is possible depends on hole diameter, seat thickness, taper, remaining wall and joint design; no general allowance is given here. Starr's pattern addressed a different failure again, out-of-round reaming.
- **Two live maker systems, not a converged standard.** Veritas's 12.8° included and the Starr-lineage 6° are both currently sold for the same kind of joint. Per Bizzarri's own comparison ("6 vs 11 degree tapers"), narrower tapers remove less wood, resist a badly wrong starting angle because more of the reamer's body bears against the pilot hole, and lock tighter once glued; wider tapers cut faster. No source located states one angle is objectively superior.

## Human Side

*Named practitioners below are quoted from their own published pages and posts. This entry is AI-compiled corpus material, not a craftsperson's testimony.*

- **Elia Bizzarri** (handtoolwoodworking.com) sells a riven-hickory 6° included-angle reamer: blade 1/16" spring steel at RC48-50, edges ground to a 70-degree bevel, tapering 3/8" to 1 1/4", "roughly 15″ overall length," depth of cut set by a set screw with a 5/32″ hex key (Reamers page, read). It is part of a $560 matched kit (reamer, three tenon cutters, dowel plate). He also sells raw bodies and standalone blades for shop-made builds, crediting blade-making instructions to Jennie Alexander (greenwoodworking.org). His pages do not state a drive method for the reamer.
- **Curtis Buchanan taught Bizzarri his reaming method** ("Curtis Buchanan taught me this method of reaming holes," read). Bizzarri's procedure: "Clamp the seat horizontally on the bench." Balance a try-square on the seat's sight line, about halfway between the hole and the seat edge, and sight from the top of the reamer through the square's edge to the sight line, setting the angle in one plane. For the second plane, "Set a bevel square to the resultant angle" **"MINUS half the taper of your reamer"** when referencing the tapered body; alternatively, set a large bevel square to the full resultant angle and align it with the reamer's cylindrical section. His worked example: a 24° resultant angle with a 6° reamer gives a 21° bevel setting (24° minus half of 6°). *(Run 615 had recorded 24° − 6° = 18°; that was wrong and is corrected here.)* Buchanan's video series ("14. Boring and Reaming the Initial Holes in the Seat," curtisbuchananchairmaker.com) shows the technique.
- **Peter Galbert** uses a section of pipe slid onto the reamer's shaft as an alignment aid, treats the blade-adjustment screw as the control for smooth cut vs. tearout across end grain, and reams immediately before assembly for fit against the specific chair. He sometimes combines tapered and straight tenons in one chair.
- **Jennie Alexander** (with Drew Langsner, Country Workshops) developed a horizontal-boring technique for post-and-rung chairs, holding posts horizontally and using a long bit extender on a brace to read the boring angle by eye before reaming (secondary sources, search-summarized).
- **Christopher Schwarz** (Lost Art Press): "People ream for way too long, which burnishes the hole and cooks the reamer" ("Tips on Tapered Reamers," 2022). In "Details on Drilling and Reaming" (2015, read), he bores a starter hole with a brace and auger at "the smallest size of the overall joint – typically 5/8” in diameter," sights against a bevel gauge taped or clamped to the underside of the seat, then reams with a cordless drill "set to a low speed and maximum torque." In the comments he identifies the tool: "It's a 12° Lee Valley reamer." The post does not say which Lee Valley model; the Veritas Pro is "built for a traditional hand brace only," so this is recorded as one practitioner's setup with an unidentified model, **not** as general technique. "Mind Upon Mind: Reaming & Drilling Leg Mortises Without a Laser" (2025) is a title-only lead, unread.
- **What the injury search found.** No first-person, named injury account tied to the reamer was located across Sawmill Creek, LumberJocks, UK Workshop, Lost Art Press, Rockler and Classic Hand Tools. That is a research result; the hazard classification below comes from the tool's mechanism and the makers' instructions.

## Proof of existence

- **No chairmaking-reamer museum accession was located in the sources checked.** A site-scoped search of Smithsonian NMAH collections for "reamer" returned unrelated reamer types (dental, tape-splice, a "Half-Round Reamer Bit," a juice reamer, trade catalogs); a direct fetch of the results page was blocked in Run 615. No per-institution search (Winterthur, Mercer Museum, Wycombe) was run.
- **No historical patent located** in the sources checked; no full DATAMP class search was run.
- **Historical existence**: Bizzarri on 18th-century blacksmith-made reamers; Schwarz on shop-made or blacksmith-made reamers in the record.
- **Current commercial existence, read directly in this pass**: Veritas Pro Taper Reamer (veritastools.ca); Lee Valley Standard Taper Reamers, Small 05J6205 and Large 05J6201; Bizzarri (handtoolwoodworking.com/reamers); Tim Manney (timmanney.com/work/reamers).

## References

| Title | Author/Source | URL | Kind | Notes |
|---|---|---|---|---|
| "Dowel & Tenon Cutter (Hollow Auger)" | this corpus | — | corpus cross-reference | sibling entry |
| "Reason Enough to Ream" | Christopher Schwarz, Lost Art Press, 2020 | blog.lostartpress.com/2020/03/07/reason-enough-to-ream | named practitioner | cylindrical default; "not terribly common" |
| "Tips on Tapered Reamers" | Christopher Schwarz, Lost Art Press, 2022 | blog.lostartpress.com/2022/04/14/tips-on-tapered-reamers | named practitioner | "cooks the reamer" |
| "Details on Drilling and Reaming" | Christopher Schwarz, Lost Art Press, 2015 | https://blog.lostartpress.com/2015/01/20/details-on-drilling-and-reaming/ | named practitioner, read 2026-10-16 | his setup; "It's a 12° Lee Valley reamer" (comment); model not stated |
| "Mind Upon Mind: Reaming & Drilling Leg Mortises Without a Laser" | Christopher Schwarz, Lost Art Press, 2025 | blog.lostartpress.com/2025/05/16 | title only, unread | lead |
| "Reamers" (product page) | Elia Bizzarri | https://handtoolwoodworking.com/reamers/ | maker, read 2026-10-16 | 6° included; Starr credit; specs |
| "Using a Chairmaking Reamer" | Elia Bizzarri | https://handtoolwoodworking.com/using-a-chairmaking-reamer/ | maker, read 2026-10-16 | clamping, chip clearing, adjustment, diagnostics, half-taper method, Buchanan credit |
| "Tools and Supplies" | Elia Bizzarri | https://handtoolwoodworking.com/tools-and-supplies/ | maker, read 2026-10-16 | reams "to a six-degree taper" |
| "Tenon Cutters" | Elia Bizzarri | https://handtoolwoodworking.com/tenon-cutters/ | maker, read 2026-10-16 | six-degree tapered tenons match his reamers |
| "Samuel Wing Tool List" | Elia Bizzarri | https://handtoolwoodworking.com/samuel-wing-tool-list/ | maker, read 2026-10-16 | "Six to eight degrees is about right"; 18th-century blacksmith-made reamers |
| "6 vs 11 degree tapers" | Elia Bizzarri | handtoolwoodworking.com/6-vs-11-degree-tapers | maker | angle-selection discussion |
| "Tapered Reamers" | Sawmill Creek forum thread | sawmillcreek.org/threads/tapered-reamers.295840 | forum, search-summarized | angle-mismatch caution |
| Tapered Reamers for Chairmaking | Tim Manney | https://timmanney.com/work/reamers | maker, read 2026-10-16 | "6 degree taper," convention unstated; $305 |
| Veritas Pro Taper Reamer | Veritas | https://www.veritastools.ca/en-ca/shop/tools/hand-tools/54865-veritas-pro-taper-reamer | manufacturer, read 2026-10-16 | hand brace only; 12.8° included; tapered square shank |
| Standard Taper Reamers | Lee Valley | https://www.leevalley.com/en-gb/shop/tools/hand-tools/drills/54864-standard-taper-reamers | manufacturer, read 2026-10-16 | one-piece; 5/16" hex; electric drill ~500 rpm, 3/8" chuck; 12.8° included |
| Veritas Tapered Tenon Cutter — Care and Use | Lee Valley | https://assets.leevalley.com/Original/10117/05J6109-veritas-tapered-tenon-cutter-care-and-use-0001.pdf | manufacturer manual `[manual, relayed]` (not reachable) | matched 12.8° cutter system, hand operation |
| "The Reamers are Here!" | Peter Galbert, Chair Notes | chairtools.blogspot.com | named practitioner, search-summarized | Starr credit; Galbert/Manney versions |
| "A Visit with Rich Starr" | Peter Follansbee, Substack | peterfollansbeejoinerswork.substack.com/p/a-visit-with-rich-starr | named author, partial (paywalled) | Starr biography; MEDIUM |
| Jennie Alexander / Drew Langsner horizontal boring | secondary sources | — | secondary, search-summarized | post-and-rung technique |
| "Reamer" / "Tapered reamer" | Wikipedia; WayKen, Travers Tool Co., Sundi/Kakele Tools | — | general reference | naming collision only |
| Smithsonian NMAH collections search, "reamer" | Smithsonian NMAH | americanhistory.si.edu/collections/search | museum search survey | no chairmaking reamer located |

## The reviewer's corrections (13)

- `BLOCKER` — 1. Separate brace-only and drill-compatible reamer families — Exact claim: The canonical definition describes the chairmaking taper reamer as “brace-driven or drill-driven,” while the anatomy and variants sections combine the Veritas Pro and Veritas Standard forms.
- `BLOCKER` — 2. Replace the empty dangerous-knowledge class with real controls — Exact claim: The dangerous section is declared “genuinely and honestly empty” because no injury anecdotes were found.
- `BLOCKER` — 3. Correct the claim that overreaming is not an injury risk — Exact claim: The access section says overreaming is a beginner trap but “not an injury risk.”
- `BLOCKER` — 4. Do not compare angle labels until their conventions are established — Exact claim: The draft presents “6° Starr/Bizzarri/Tim Manney” and “12.8° included Veritas” as two non-interchangeable current standards.
- `BLOCKER` — 5. Remove the glue-independence and self-locking assurance — Exact claim: A matched taper is said to “seat and lock tight” and provide a joint “without glue-dependent strength alone.”
- `BLOCKER` — 6. Remove direct boring as a substitute for a required tapered mortise — Exact claim: For a one-off joint, careful direct boring is presented as an alternative when reamer setup is not worthwhile.
- `BLOCKER` — 7. Do not generalize powered use or “maximum torque” guidance — Exact claim: Christopher Schwarz's use of a cordless drill on low speed and maximum torque is presented as generally applicable taper-reamer technique.
- `SHOULD-FIX` — 8. Make pilot-hole dimensions model- and joint-specific — Exact claim: The procedure instructs the user to bore an approximately 5/8-inch pilot hole.
- `SHOULD-FIX` — 9. Attribute blade setting and sound diagnostics to the correct design — Exact claim: Squeaking means clear chips or advance the blade, while chatter means retract it, as though this diagnosis applies to taper reamers generally.
- `SHOULD-FIX` — 10. Qualify the compound-angle formula and correction claim — Exact claim: The draft presents a subtract-half-the-taper arithmetic method and says a tapered joint can correct a mis-bored angle by about ten degrees.
- `SHOULD-FIX` — 11. Narrow the Richard Starr origin claim — Exact claim: Richard Starr is described as the originator of the chairmaking taper reamer design.
- `SHOULD-FIX` — 12. Reframe historical absences and weak artifact evidence — Exact claim: The historical section uses unsuccessful patent and museum searches, plus a privately held circa-1780 object, to characterize the record.
- `MINOR` — 13. Remove process residue and keep confidence calibrated — Exact claim: The entry includes research-process narration, search summaries, and references to its position as a “second chairmaking entry.”