# Forstner Bit Hewn Tool Library · https://hewn.build/tools/forstner-bit Corrected: An independent reviewer read this entry and found corrections. They have been applied to the text, and the reviewer re-checked the correction that mattered most for safety and found it done; the others have not been re-checked yet. The list at the end is the record of what changed. Cite as: "Forstner Bit." Hewn Tool Library, hewn.build/tools/forstner-bit. Reviewed 2026-08-31. --- ## identity **Name:** Forstner bit (also Forstner drill bit, Forstner auger). Named for its inventor, Benjamin Forstner. **Two unrelated naming collisions confirmed by direct search, worth flagging so a reader never conflates them:** the **Forstner Chain Corporation** (a jewelry/watch-bracelet maker founded ~1920 in New Jersey, known for the "Komfit" band and NASA Speedmaster bands) and **FORSTNER** (an Austrian sheet-metal coil-line machinery maker, Feldkirch, since 1960). Neither has any connection to the boring bit or to Benjamin Forstner. **Family / category:** A rim-guided wood-boring bit — cuts with a circular (or partial-circular) peripheral rim rather than a center lead screw, which is the single fact that defines everything else about the tool. This corpus's own [[Auger]] entry already frames the Forstner as the auger's direct "negative" — the auger self-feeds via a lead screw and cannot make a flat-bottomed blind hole because the screw always projects past the cutters; the Forstner has no lead screw and so cannot self-feed, but can stop cleanly at a flat bottom. Twist Drill Bit similarly names the Forstner as its own "negative in wood" — a conical center-point tool cannot make a flat floor; a rim-guided tool can. **One-line:** A drill bit that cuts with its rim instead of a screw tip, which is why it can bore a flat-bottomed hole, stop partway into a board, overlap a previous hole, or start on only part of its own circumference — none of which a lead-screw or center-point bit can do. --- ## ✦ how NOT to use it **not-for.** Not for metal unless the exact cutter manufacturer explicitly approves that material and supplies its own machine, speed, feed, lubrication and workholding instructions; otherwise use a metal-rated cutter (see Matching). Not for a portable setup the cutter maker does not approve — without a long self-centering point, freehand control degrades as diameter and interrupted engagement rise; match by the maker-approved machine and setup, not a fixed diameter. Not a deep-boring tool — its closed-rim geometry clears chips far worse than an auger's open helical flute, and (counterintuitively) smaller-diameter Forstners clog worse than large ones for the same reason. **dangerous.** *(Round 2, Fix 4: the earlier "genuinely thin" framing — treating a thin Forstner-specific injury record as the danger class — is withdrawn. A boring bit can badly injure without an incident report naming its subtype; the hazards below come from machine and drill manuals, organised by mechanism. The manual for your own press or drill governs.)* **Workpiece rotation or ejection:** "Clamp workpiece to table or in table-mounted vise, or brace against column to prevent rotation" and "NEVER hold workpiece by hand during operation," because "An unsecured workpiece may unexpectedly shift, spin out of control, or be thrown" [Grizzly G0756](https://cdn1.grizzly.com/manuals/g0756_m.pdf); with a portable drill, "Secure the material being drilled. Never hold it in your hand or across legs" [Bosch drill manual](https://www.boschtools.com/us/en/ocsmedia/r00016v1.pdf). **Startup and setup:** "Never leave chuck keys, wrenches, or any other tools on machine. Always verify removal before starting!" and "NEVER start machine with bit/cutting tool touching workpiece; allow spindle to gain full speed before drilling" [Grizzly G0756](https://cdn1.grizzly.com/manuals/g0756_m.pdf); seat and tighten the cutter in the chuck and inspect it (cracked, bent or dull cutters out) before starting (reviewer recommendation, the reviewer's 2026-08-31 review). **Entanglement:** "DO NOT wear loose clothing, gloves, or jewelry. Tie back long hair" [Grizzly G0756](https://cdn1.grizzly.com/manuals/g0756_m.pdf); keep hands away from the cutter. **Eyes and face:** "Flying chips created by drilling can cause eye injuries or blindness. Always wear a face shield in addition to safety glasses" [Grizzly G0756](https://cdn1.grizzly.com/manuals/g0756_m.pdf); "Always wear safety goggles or eye protection when using this tool" [Bosch drill manual](https://www.boschtools.com/us/en/ocsmedia/r00016v1.pdf). **Binding and reaction torque (portable drill):** "Always use auxiliary handle for maximum control over torque reaction or kick-back" and "Position yourself to avoid being caught between the tool or side handle and walls or posts," since a bound bit's "reaction torque of the tool could crush your hand or leg" [Bosch drill manual](https://www.boschtools.com/us/en/ocsmedia/r00016v1.pdf); "If the bit becomes bound in the workpiece, release the trigger immediately," then "reverse the direction of rotation and slowly squeeze the trigger to back out the bit," and "Be ready for a strong reaction torque" [Bosch drill manual](https://www.boschtools.com/us/en/ocsmedia/r00001v1.pdf); "Do not pull the trigger on and off to attempt to start a stalled bit" [Milwaukee drill manual](https://documents.milwaukeetool.com/58-14-1700d9.pdf). On a drill press, switch off and let the spindle stop before freeing a jammed bit or workpiece (reviewer recommendation; check your press manual). **Hot cutter and sharp edges:** chips and the cutter can be hot and sharp after a bore; let the cutter cool before touching it and handle it by the shank (reviewer recommendation from the reviewer's 2026-08-31 review — the Grizzly manual read this pass has no hot-bit warning). **Interrupted cuts:** overlapping, edge and angled holes load the cutter unevenly; do them only in a rigid, supported jig with a cutter its maker approves for the operation (reviewer recommendation, the reviewer's 2026-08-31 review). **Honest gap, kept but not used as the hazard rating:** no Forstner-bit-specific documented injury account was located in the original research; that absence does not lower the hazards above. **damaging.** Overheating and burning from running outside the maker's chart for the bit's diameter and the wood's hardness — the single most repeated failure across the forum record (see Human Side and Access). Excess heat can scorch the work, accelerate dulling, damage coatings or brazing, and — depending on cutter alloy and temperature — reduce hardness; carbide improves wear and heat resistance but does not make burning impossible. *(Round 1 fix 8: the earlier "loses the bit's temper permanently" is withdrawn as a universal claim; state the cutter's material when diagnosing.)* Jamming or seizing in a deep hole is documented first-hand (a Sawmill Creek account of a bit jammed roughly 7–8" deep, a drill extension pulling loose, and the exposed shank needing to be vise-gripped free) — MEDIUM, a single but detailed first-hand account. Sharpening the wrong face of the cutting lip rounds it over and kills the cut entirely — named-poster diagnostic: "does the bit spin on the wood and burnish it, or does the bit stop turning? If it spins, it's had the cutting lip rounded over" (badger1805, Fine Woodworking forum). **beginner-trap.** Forcing a large-diameter hole in one deep, uncleared pass — the safer beginner route is staged depth, regular chip clearing, a controlled feed, and a cutter and machine sized for the job. *(Round 1 fix 10: the forum "facing" method — score at full diameter, hog the centre with smaller bits, return with the full-diameter bit — is removed from beginner guidance. It is specialist technique with no authoritative cutter or machine source here, and removing the centre can leave a center-pointed bit without purchase, so re-engaging a large cutter in an interrupted hole can raise chatter, grabbing and loss of control. Kept only as practitioner record: Thomas Canfield, Sawmill Creek, MEDIUM.)* Not clearing chips periodically on a deep hole, letting the flutes pack and the bit stall or burn (Richard Coers, Prashun Patel — corroborated across two independent threads, MEDIUM). Treating "run large bits slow" as a fixed, universal RPM rule rather than drive-mechanism-dependent guidance — the corrected finding from Sarge/Wilbur Pan above. Sequencing a pilot hole before a larger counterbore instead of after — Popular Woodworking's own named tip flags this directly, and notes a Forstner is one of the few bit types that can actually recover from the mistake (bore the larger hole centered over the smaller existing one), which most other bit types cannot do — a genuinely useful, sourced, non-obvious point (MEDIUM-HIGH, named trade author). **lineage-misuse.** Treating a Forstner like an [[Auger]] and expecting it to self-feed — a Forstner has no lead screw, so it must be fed with sustained, even hand or quill pressure the whole way through, not "let the screw pull it in." Treating it like a twist drill or spade bit and expecting a center-point-only guide with aggressive axial pull — a Forstner needs the *rim* engaged first (spindle started with the bit clear of the work and up to speed, then fed until the rim scores a full circle — see Correct Use); pushing hard on the center spur alone, the way a twist-drill habit teaches, tends to either stall the bit (too little rim register) or force and burn it (too much pressure without full rim contact). **Confidence note:** this pairing is a reasoned synthesis of two well-sourced facts already established in this corpus (the Auger and Twist Drill Bit entries' own "no lead screw / no cone point" claims about the Forstner) plus the repeated forum "why won't it bite" troubleshooting pattern documented above — MEDIUM, not a single source stating the mechanism explicitly in these terms. Running it like a spade bit — punching straight through at full pressure without backing the exit face — can still tear the far face even though the rim's entry was clean, since the rim scores the boundary but does not protect the exit the way a backer board does; this is a direct extension of the same exit-blowout pattern this corpus's boring-family entries already document for the auger and twist drill. --- ## correct use **Genuinely good at:** clean, flat-bottomed, non-wandering holes — including holes that overlap a previous bore, enter at an angle, or sit only partway on a board's edge, none of which a lead-screw or center-point bit can do. **How to use it well (short version — the workbench holds the deep operation):** clamp the workpiece; with the bit clear of the work, start the spindle and let it reach the speed the cutter and machine makers specify — "NEVER start machine with bit/cutting tool touching workpiece; allow spindle to gain full speed before drilling" ([Grizzly G0756 drill-press manual](https://cdn1.grizzly.com/manuals/g0756_m.pdf)) — then feed lightly until the peripheral edge scores a complete circle, and continue at a controlled feed; a Forstner needs the rim engaged to register, unlike a self-feeding auger; back the exit face with sacrificial scrap, since the rim's clean *entry* does not guarantee a clean *exit* — several independent trade sources note real, sometimes dramatic exit blowout without a backer board; on deep or small-diameter holes, withdraw periodically to clear chips rather than boring straight through, since smaller bits clog faster than large ones once the rim buries past its own gullets (a finding from a FAMAG-published bit test, corroborated by forum practice — MEDIUM-HIGH). --- ## ✦ matching — the workbench's first read **does:** bores flat-bottomed holes · bores overlapping holes without wandering (hogging out mortises, recessed inlays) · bores partway into a surface without blowing through, given a depth stop · bores partial/edge holes — the named, sourced example is a figure-eight tabletop fastener slot, described directly as "the only drill bit that can drill this style of hole" (Stumpy Nubs Woodworking Journal — MEDIUM, single trade-blog source for this specific claim, though the underlying mechanism is architecturally consistent with the rim-guidance logic established above) · bores at an angle, with less certainty than the other claims — the rim needs near-full contact to register, so a shallow-angle start is harder than for a self-feeding auger (reasoned from the anatomy, not independently sourced) · bores relatively clean end-grain and near-edge holes on entry, though exit tear-out is a real, separately-documented risk without a backer board (see Correct Use). **suits:** cabinet hinge-cup boring in portable or drill-press work with a 35 mm Forstner-pattern bit (carbide-tipped is the named trade choice); not production hinge-machine boring, which takes a distinct hinge/cylinder boring bit — do not match on "35 mm" or "hinge cup" alone: ask whether the user has a portable drill, drill press, CNC/hinge-boring machine or line-boring machine, and what shank and rotation that machine requires · shelf-pin holes · dowel joinery · plug and counterbore holes · mortise-hogging via overlapping bores · large-diameter through-holes in clockmaking (Popular Woodworking names this a favorite clockmaker's use) · figure-eight tabletop-fastener slots at a board's edge. **kit-fit:** - *Pairs with:* the machine the cutter's maker approves it for — current makers rate some Forstner bits "For portable drills or stationary machines" ([Bosch Forstner bits](https://www.boschtools.com/us/en/forstner-bits-43523-ocs-ac/), fetched 2026-10-16). Torque and loss-of-control risk generally rise with diameter and with interrupted (overlapping, edge, angled) cuts, so larger or asymmetrical work often favours a drill press or boring machine for accuracy and registration; but no universal diameter cutoff decides whether portable use is safe — that depends on the exact cutter, drill torque, auxiliary handle, speed range, workholding, hole geometry and operator control. *(Round 1 fix 9: the earlier "effectively mandatory above roughly 1"" and "1"–2"" thresholds are withdrawn as rules; this corpus's [[Drill Press]] entry still carries the 1" figure [DP13][DP30] and should be read as that entry's guidance, not a cutoff.)* - *Substitutes for:* a hole saw in the size range both cover — Forstners commonly run 1/4"–2-1/4", hole saws 1"–6", so the overlap band (roughly 1"–2-1/4") is a real choice point: Forstner wins on hole quality and a true flat bottom, hole saw wins on speed and reaches larger diameters the Forstner line doesn't. Also substitutes for an auger bit in short, shallow-hole work — but not deep boring, where the auger's open helical flute clears chips far better than the Forstner's more closed rim design (this corpus's own [[Auger]] entry already frames this relationship from the auger's side). - *Cannot replace:* a production hinge/cylinder boring bit on a hinge-boring, automatic boring or CNC machine — a related but distinct cutter family (see Lineage), with its own geometry, machine shank and cutting direction. A 35 mm Forstner-pattern bit bores hinge cups in portable or drill-press work; it is not interchangeable with the machine cutter just because the diameter matches. **not-for (project-keyed):** deep holes, where chip-clearance failure is a real, sourced problem — and counterintuitively, **smaller-diameter bits clog worse than large ones**, because larger bits have proportionally larger gullets to evacuate chips (a FAMAG-published bit-test finding, corroborated by forum accounts of end-grain holes clogging within about an inch of depth) · portable-drill work the cutter maker does not approve, or large or interrupted cuts without rigid workholding — control degrades as diameter and asymmetrical engagement rise, but no single diameter is the cutoff · metal — do not use a wood-rated Forstner bit in metal unless the exact cutter manufacturer explicitly approves that material and supplies compatible machine, speed, feed, lubrication, and workholding instructions; otherwise use a metal-rated boring cutter (round 2: the earlier off-label aluminum procedure is removed) · a bit needing a truly markless flat bottom — standard modern Forstners leave a small center-spur dimple; only the "without pilot or spur center" sub-category avoids it. **access:** low skill floor for basic use — clamp the work, start the spindle with the bit clear of the stock, let it reach the specified speed (round 3, Fix 5: Grizzly G0756 p.10 says to allow full spindle speed before drilling), then feed until the rim scores a full circle, back the exit with scrap. **Speed (round 2, Fix 2):** use the speed chart supplied for the exact cutter and the exact machine, adjusted for diameter and stock. This entry gives no generic RPM band and no "slower is safer" rule: one drill-press manual warns that "Larger bits turning at slower speeds tend to grab the workpiece aggressively," and calls its own diameter-by-material spade/Forstner speed chart "a guideline only" [Grizzly G0756 drill-press manual](https://cdn1.grizzly.com/manuals/g0756_m.pdf). If the cutter has no trustworthy maker chart, do not invent one — get the chart from the cutter and machine makers before boring. Drive mechanism matters too: a Sawmill Creek practitioner (Wilbur Pan) explains that electronic speed controllers lose torque as RPM drops while step-pulley presses do not (see Human Side) — practitioner texture for why one number cannot serve every press, not a chart. **revival:** the concrete hook is not "Forstners are nice" but that specific, named joinery operations — partial edge holes, overlapping mortise-style bores, true flat-bottomed hinge cups — have no substitute among the common bit types a maker is likely to already own. A maker reaching for a Forstner is usually reaching for it because nothing else in the kit can do that specific cut. --- ## anatomy - **Center point / brad point / spur.** A small point that positions the bit; on the *original* 1874 Forstner it did not exist at all — the bit was guided solely by the rim, "hard to position" but leaving a fully clean, flat-bottomed hole with no center mark. Most bits sold today under the Forstner name have re-added a spur for starting control, which leaves a small dimple at the center of the hole (Roland Johnson, *Fine Woodworking* #197 — HIGH, a named contributing editor's dated, detailed comparative test, the strongest secondary source in this entry). A real, named sub-category — "Forstner bit without pilot or spur center" — is still sold for makers who need a truly markless bottom. - **Peripheral rim / score edge.** The outer circular (or partial-circular, on milled/slotted patterns) cutting edge, which contacts the wood first and severs the fibers around the hole's circumference before the interior cutters remove the waste — the direct mechanical descendant of what Forstner's own 1886 patent calls the "peripheral cutting-edge," read verbatim above. This is *why* the hole wall comes out clean: the boundary is cut before it's disturbed. - **Interior cutting lips / chippers.** The angled internal blades (Forstner's own patent term: "cutting-lips") that pare the bulk of the waste inside the already-scored circle. Per the 1886 patent, verbatim: "the chips which are afterward separated from the wood by the cutters... being already separated at the periphery of the hole, will be removed without tearing or roughening the inner surface of the wood." - **Why rim-guidance permits overlapping, angled, and partial holes** — the mechanical reason, not just the claim: because the bit registers on the rim's own contact with the wood rather than a center screw seeking purchase on-axis, it only needs *some* portion of its circumference and depth engaged to stay controlled — so it tolerates a hole that overlaps a prior one, enters at an angle, or is bored partway off a board's edge, none of which a lead-screw or center-point tool can do (Popular Woodworking, Bruce Kieffer — MEDIUM-HIGH, named trade author, not a peer-reviewed engineering source). - **Governing standard: DIN 7483.** *(Corrected after the reviewer's 2026-08-31 review; the earlier "no governing engineering standard found" is withdrawn.)* [DIN 7483:2024-11](https://www.dinmedia.de/en/standard/din-7483/384106644), *"Wood bits - Forstner bits and hinge boring bits,"* replaces DIN 7483:1966-11; per the DIN Media summary it revises forms A and E (extended to 10–100 mm), removes forms C and F, and adds a sheathed hex-shank Forstner form H, a two-edge form K, and hex-shank, three-flat-shank and carbide-insert variants (fetched 2026-10-16). Current products cite it: Fisch marks its Wave Cutter "DIN 7483G" ([Fisch](https://www.fisch-tools.com/en/produkte/0317-wave-cutter-forstner-bit)); the reviewer reports Bosch products also identify DIN 7483 G *[manual, relayed — the Bosch Forstner page fetched this pass does not mention DIN]*. The standard defines forms and dimensions; individual products still differ in edge geometry, material, shank, and approved machines. --- ## variations (living) *These variations sit on different axes — edge form (continuous rim, saw-tooth, wave-edge), cutter material (tool steel, HSS, carbide-tipped), and centre (spur or none) — not one mutually exclusive list. Name the cutter material explicitly when matching.* - **Plain-rim Forstner**, continuous or partial rim, center spur — the common pattern sold by nearly every major toolmaker (Bosch, Grizzly, Porter-Cable, Woodcraft, Freud, Fisch, Famag, all tested head-to-head in the 2008 *Fine Woodworking* comparison), made in tool steel, HSS, or carbide-tipped forms; no one material is the baseline. HSS is marketed for heat tolerance over carbon steel: "heat build-up will not soften them, as will happen with carbon steel" ([Lee Valley HSS Forstner set](https://www.leevalley.com/en-us/shop/tools/power-tool-accessories/drill-bits/102814-set-of-7-imperial-hss-forstner-bits-with-wooden-box), fetched 2026-10-16). - **Carbide-tipped Forstner** — brazed carbide edges; better wear and heat resistance, holds an edge through melamine/MDF far longer than HSS, but does not make burning the work impossible; costs more and is harder to resharpen. Named by Popular Woodworking as the trade choice for hinge-cup boring in portable/drill-press work (MEDIUM-HIGH); production hinge machines use distinct hinge boring bits (below). - **Multi-Spur / sawtooth** — serrated peripheral rim; more aggressive on end grain, real chatter/tear-out tradeoff at the start of a cut; origin unconfirmed (honest gap, see Lineage). - **Wave Cutter** (Fisch, Austria) — forged, with a patented wavy peripheral cutting edge, reduced heat generation and large chip clearances per Fisch's current page; marked DIN 7483G (see Lineage; the earlier 25%/30-resharpenings figures are withdrawn as unsourced). - **Bormax** (FAMAG, Germany, est. 1865) — patent-protected cutting geometry with a waveform body and staggered chip-breaker edges. - **35 mm hinge-cup boring** — a 35 mm Forstner-pattern bit serves portable and drill-press installation; production hinge/cylinder boring bits (two main cutters, two spurs, centre point, carbide tips, machine shanks, a set cutting direction) are a related but distinct family under the same DIN 7483 title (see Lineage). Match by form, shank, rotation and machine, not by the 35 mm figure. - **"Without pilot or spur center"** — a real, named sub-category closer to Forstner's own original 1874 design, for makers who need a truly markless flat bottom. **Real current market (fetched/checked 2026-07-20):** sizes commonly run **1/4" to 2-1/4"** across trade-comparison sources. Freud (Woodcraft): Precision Shear 16-pc HSS set $364.97, single bit $10.47, carbide-tipped single $31.97; a separate Freud standard HSS 16-pc set (FB-107, Midwest Technology) $83.80. CMT 16-pc set with case, roughly $125–$150 across most retailers. *(Wood Owl removed from this Forstner list after the reviewer's 2026-08-31 review: Lee Valley describes Wood Owl bits as having "strong, sharply defined lead screws, and three spurs," "triple flutes," "high-carbon steel with a low-friction PTFE coating" and 7/16" hex shanks ([Lee Valley](https://www.leevalley.com/en-us/shop/tools/power-tool-accessories/drill-bits/75748-wood-owl-bits), fetched 2026-10-16) — a screw-fed, auger-family design, useful only as a contrast to the rim-guided Forstner.)* Fisch's carbide/"Black Shark" line runs from ~$11 per bit. Lee Valley sells 7- and 13-piece Imperial HSS sets. **Flagged, not confirmed:** a currently-active, distinctly-branded Vermont American Forstner line separate from Irwin/Marples — searched and not confirmed. --- ## trades **Cabinetmaking/furniture** — mortises via overlapping bores, plug and dowel holes, tabletop-fastener edge holes; the primary trade home for this tool. **Cabinet hardware installation** — 35 mm European concealed-hinge cup boring is a distinct, industry-standard sub-trade use. In portable and drill-press installation, carbide-tipped 35 mm Forstner-pattern bits are the named trade choice because they hold an edge through repeated boring in melamine and MDF where HSS dulls fast; production shops on hinge-boring, automatic boring or CNC machines use hinge/cylinder boring bits, a related but distinct cutter family (see Lineage). **Clockmaking** — large-diameter Forstner bits (up to 4") named as a favorite for precise large through-holes (Popular Woodworking, MEDIUM-HIGH). **Woodturning** — lathe-mounted, tailstock-chuck use for hollowing recesses, candle sockets, and turning-blank mounting holes is well-documented in the forum record, though several first-hand accounts note the technique differs from drill-press use (less mechanical leverage, working in graduated steps, active chip-clearing needed). **General construction/finish carpentry** — general large-hole boring (conduit/pipe pass-throughs) is mentioned in passing across aggregator sources but not deeply verified this run — flagged as lightly sourced. **Metalworking** — not a use this entry supports: no metalworking-trade adoption was found, unlike the twist drill's genuine metalworking origin, and the entry gives no metal procedure; metal only where the exact cutter maker explicitly approves it (see Matching). **Masonry/stone** — no use found and none plausible; the same flat-rim/paring-lip geometry logic this corpus's Twist Drill Bit entry uses to rule out masonry for HSS twist bits applies here, and this is a reasoned exclusion, not a directly sourced claim. --- ## lineage **Ancestors.** The **auger / spiral auger bit** (lead-screw self-feed; cannot stop flat or bore partial-rim holes — see [[Auger]]) and the **twist drill / [[Spade Bit (Paddle Bit)|spade bit]]** (center-point guided, conical floor, prone to wandering and blowout at entry/exit, cannot hold a line in end grain or at an angle). The Forstner is not a refinement of either — it is a different mechanism (rim-guided vs. screw-fed vs. point-guided) built to do the one job neither could: a clean, flat-bottomed, non-wandering hole. **Descendants / contemporaries.** - **Carbide-tipped Forstner** — brazed carbide edges; improves wear and heat resistance and holds an edge through abrasive sheet goods (melamine, MDF) far longer than HSS, but does not make scorching the work impossible. Common in portable and drill-press hinge-cup work; production hinge machines use a related but distinct carbide hinge/cylinder boring bit (see the 35 mm bullet below). - **Multi-Spur / sawtooth Forstner** — a serrated peripheral rim instead of a continuous scoring edge; more aggressive, better in end grain, but prone to initial chatter. **Honest gap:** no inventor, originating company, or patent could be found for the "Multi-Spur" name or pattern specifically, despite direct search — carried as a real current product category (W.L. Fuller, Greenlee) with an unknown origin, not glossed over as settled history. - **Wave Cutter** (Fisch, Austria) — a genuinely distinct, forged design with a patented wavy ("serrated") peripheral cutting edge that Fisch says generates "considerably less heat," plus "large chip-free zones" for chip discharge and a three-flat shank; Fisch marks it "DIN 7483G" ([Fisch product page](https://www.fisch-tools.com/en/produkte/0317-wave-cutter-forstner-bit), fetched 2026-10-16). *(The earlier "25% lower cutting resistance" and "resharpenable up to 30 times" figures are withdrawn: neither appears on Fisch's current product page or product sheet, and no dated Fisch document carrying them was located.)* - **Bormax** (FAMAG, Germany) — a company-patented cutting geometry (toothed main edges, grooved circumference cutter, staggered chip-breaker edges); patent number not independently verified. - **35 mm hinge-cup holes — two related, distinct cutter families (corrected after the reviewer's 2026-08-31 review).** A 35 mm hinge-cup hole may be bored with a 35 mm **Forstner-pattern bit** in portable or drill-press work; several retailers checked in the original research (RokHardware, Milescraft, HardwareSource, D. Lawless Hardware) sell portable-installation 35 mm bits as Forstner-pattern products. But **production hinge/cylinder boring bits are a related, distinct cutter category**, not a Forstner by diameter: the current standard is titled *"Wood bits - Forstner bits and hinge boring bits"* ([DIN 7483:2024-11](https://www.dinmedia.de/en/standard/din-7483/384106644)); Fisch lists "Forstner bits" and "hinge boring bits" / "TCT hinge boring bits" as separate families ([Fisch](https://www.fisch-tools.com/en/produkte/0310fsg-forstner-speed-grinder)); and a LEUCO carbide cylinder boring bit is specified with "2 rakers, 2 spurs and centering point," a "cylindrical shank with clamping surface," a stated cutting direction, and use on "hardware hinge machines," "automatic boring machines," and "CNC machining centers" ([LEUCO](https://www.leuco.com/EN/US/Boring_Bits/Cylinder_Boring_Bits/Cylinder_Head_Drill_Bits_HW_Z_2_2/1000118337)) (all fetched 2026-10-16). Match by cutter form, shank, rotation, machine, and manufacturer-rated application — not diameter alone. *(The earlier "not a separate tool" finding is withdrawn.)* **Contemporaries doing the job differently, not descendants.** The **[[Self-Feed Bit]]** (spade-bit family, has a lead screw, built for speed on large rough construction holes; now its own entry, Haft Run 654) and the **hole saw** (a thin cylindrical blade that cuts only the rim and leaves a solid core, no flat bottom) each solve a related problem — a large hole — with a different mechanism and a different tradeoff. Popular Woodworking's own comparison treats these explicitly as alternatives to reach for instead of a large Forstner, not as tools descended from it. --- ## history **Benjamin Forstner** (25 March 1834 Beaver County, PA – 27 Feb 1897 Salem, OR) — gunsmith, inventor, dry-goods merchant. Emigrated west with the Aurora Colony (a communal Utopian settlement under William Keil) in 1863, settled and established as a gunsmith in Salem, Oregon by 1865. *(Source: Wikipedia, "Benjamin Forstner" — MEDIUM, an aggregator source, but internally consistent and cross-corroborated by the independent patent and tool-historian sources below.)* **Two patents, not one.** - **US 155,148**, "Improvement in Augers," granted 22 September 1874 — the original patent; the Google Patents OCR reads "application filed August" with the day lost, so no exact filing day is given here. DATAMP's cataloguer, paraphrasing the patent's own claim language, describes "the circular cutting band and cutting lip located in nearly the same horizontal plane." Surviving marked examples are stamped "BF" and the patent date. **Read on Google Patents 2026-10-16** ([US155148A](https://patents.google.com/patent/US155148A/)): "The circular band serves to guide the bit accurately in its movement" and "give the hole that is bored a smooth and perfect finish"; "By its employment the gimlet-point may be dispensed with"; and "there is no tendency to split the wood or to follow the grain." *(HIGH — primary source. Correction from the reviewer's 2026-08-31 factual notes: the original draft said this text could not be located.)* - **US 336,709**, "Auger," granted 23 February 1886, one-half assigned to James Walton of Salem — the improvement patent, and the one that gives the tool its recognizable milled-slot construction. **Read verbatim this run** (Google Patents). Forstner's own patent text states the failure being fixed: *"In augers of this class heretofore in use the peripheral cutting-edge has been a complete circle, and the oppositely-arranged cutting lips... have formed at their junction with the cutting-edge enlargements, which interfered with the free working of the auger, and the peripheral cutting-edge required considerable pressure to force it into the wood being bored."* His fix — bisecting the rim with two angled milled slots — was explicitly stated to be cheaper to manufacture, easier to sharpen, and to give "a ready escape for the chips." *(HIGH — primary source, read in full.)* A **Canadian patent, CA 23548** ("Auger," published 6 March 1886), is cited via Wikipedia/Espacenet but not independently verified beyond that citation — MEDIUM. **What the original 1874 design fixed, and why a gunsmith built it — corroborated across sources but not confirmed in Forstner's own 1874 language.** Secondary and named-historian sources converge: the bit "did not feature the lead screw... or the cutting lips of more conventional wood boring bits" and "excelled at boring smooth-sided, flat-bottomed holes... at an angle and not following the grain of the wood" — better, for that purpose, than the Russell Jennings twist augers of the day (Wikipedia, MEDIUM; independently corroborated in substance by named tool historian **Randy Roeder**, oldtoolheaven.com — a source class this corpus already treats as MEDIUM-HIGH via its citations in the Auger and Brace and Bit entries). That a gunsmith needed exactly this — clean, precisely located, flat-bottomed, non-wandering holes in gunstocks and hardware, without an auger's tendency to follow the grain or a lead screw's tendency to punch through and split at an angle — is a reasonable inference from his occupation and the design, not a directly quoted patent statement. Flagged as inference, MEDIUM. **Manufacturing and diffusion.** Forstner did not manufacture at scale himself; he licensed production to **Colt's Manufacturing Company** (Hartford) and the **Bridgeport Gun Implement Company**, and by the mid-to-late 1890s the **Connecticut Valley Manufacturing Company** (CONVALCO) also produced the line, evidenced by exhibition dates printed on its bit-box labels. Forstner reportedly showed bits at the 1876 Centennial Exhibition (Philadelphia) and the 1893 World's Columbian Exposition (Chicago) — sourced only to Wikipedia's single line, not independently corroborated; flagged MEDIUM. CONVALCO carried the Forstner line until a 2011 sale to Morris Wood Tool Company (Roeder). A period two-page illustrated trade catalog, *"Need a Better Bit? Use the Forstner,"* Connecticut Valley Manufacturing Co., survives scanned in the Internet Archive's International Tool Catalog Library — real, dated documentary proof of commercial production into the CONVALCO era. A named period trade-press mention — *Carpentry & Building*, July 1883, discussing Forstner bits from a maker DATAMP names as "Forstner, Sharp & Co." — is confirmed to exist (linked from DATAMP via a Google Books scan) but was not itself fetched and read this run; flagged as a real follow-up, not asserted content. **The self-narrated fix is a two-layer Petroski story.** The 1874 original fixed the auger/twist-drill/spade-bit family's inability to make a flat-bottomed, non-wandering, angle-tolerant hole. The 1886 patent then fixed the *original Forstner bit's own* manufacturing cost and chip-clogging problem — a tool correcting its own prior version's failure, in the inventor's own words, twelve years apart. **Modern retrospective correction, worth carrying into anatomy.** The original 1874 bit had no center spur at all — it was guided solely by the rim. Most bits sold under the Forstner name today have re-added a small center point/spur for starting control (see Anatomy) — a real design drift from Forstner's own original, not a return to it. --- ## human side **Roland Johnson**, contributing editor, *Fine Woodworking* — ran the most rigorous documented comparative test of the tool found in this research: 18 brands, measured hole-diameter accuracy to 0.005", an overlapping-hole test, and an angled-hole test, published as "Tool Test: Forstner Bits," *Fine Woodworking* #197 (Mar/Apr 2008). *(HIGH on methodology and general findings; the per-brand rankings sit behind a paywall and were not retrieved — flagged.)* **Randy Roeder**, oldtoolheaven.com — a tool historian already trusted elsewhere in this corpus (cited at MEDIUM-HIGH in the Auger and Brace and Bit entries). His piece on the Connecticut Valley Manufacturing Company is the best single secondary account of Forstner's own licensing arrangements and the bit's 19th-century commercial diffusion. **A named, dated, mechanically substantive forum myth-bust — Sawmill Creek, "Large Forstner Bits.. Exposing the MYTH" (Jan 2009).** Poster **John Thompson ("Sarge")** ran a hands-on RPM test with a 2⅛" carbide Forstner across a range of drill-press speeds: 240 rpm produced squealing and stalling, 990 rpm produced excessive grab, ~600 rpm gave a clean cut. Poster **Wilbur Pan** supplied the mechanical explanation that makes this more than one anecdote: electronic speed controllers lose torque as RPM drops, while step-pulley-drive presses do not — so the "right" RPM for a large bit depends on the press's drive mechanism, not a single universal number the way the folk rule ("run large bits slow") implies. Kept as practitioner texture — one bit, one press, one session; the three speeds are not an operating chart, and Access below defers speed to the exact cutter and machine maker's chart. It remains a useful correction against a repeated but imprecise piece of shop folklore. **Two further named-poster forum threads, both diagnosing real failures, both corroborating the same underlying misuse causes** (Sawmill Creek "Forstner bit problems," 2020, with **Dave Mount**, **Richard Coers**, **John K. Jordan**, **Prashun Patel**; Fine Woodworking forum "3" forstner bit jamming," 2022, with **badger1805**, **Myko**, and **derekcohen**). Consensus diagnoses across both threads: a dull bit, insufficient drill/press torque relative to bit diameter, and a cutting lip rounded over by incorrect sharpening (badger1805's specific diagnostic: "does the bit spin on the wood and burnish it, or does the bit stop turning? If it spins, it's had the cutting lip rounded over.") — this is real, first-hand, named-poster troubleshooting knowledge, not manufactured. **derekcohen** is Derek Cohen ("In The Woodshop"), a named woodworker already cross-referenced in this corpus's [[Holdfast]] entry — a small but real point of independent cross-corroboration between two Haft entries built in different runs. **No named master-craftsman profile or biography specific to the Forstner bit was found** (unlike, e.g., this corpus's Holdfast entry, which carries named blacksmiths). The tool's accessible human-side record is dominated by one named trade-press tester (Johnson) and pseudonymous-but-substantive forum practitioners, not profiled masters. Flagged as a genuine, checked gap rather than papered over. --- ## ✦ proof of existence **Original patent:** US 155,148, granted 22 September 1874 to Benjamin Forstner of Salem, OR, "Improvement in Augers." Existence, date, and general claim independently confirmed across DATAMP, Wikipedia, and Randy Roeder's tool-historian account; the text itself read on Google Patents 2026-10-16 (see History) — HIGH. **Improvement patent, read verbatim:** US 336,709, granted 23 February 1886 — full text read directly on Google Patents. HIGH. **Canadian patent:** CA 23548, "Auger," published 6 March 1886 — cited via Wikipedia/Espacenet, not independently re-verified. MEDIUM. **Named-collector/period documentation:** DATAMP's cataloguer notes surviving examples stamped "BF" and the patent date, and references two physically distinct early types documented from a boxed set made by "Forstner, Sharp & Co." A named period trade-press mention (*Carpentry & Building*, July 1883) is confirmed to exist via a Google Books scan linked from DATAMP, but was not itself fetched and read this run — flagged as a real follow-up. A 2-page illustrated trade catalog, "Need a Better Bit? Use the Forstner," Connecticut Valley Manufacturing Co., survives scanned in the Internet Archive's International Tool Catalog Library — HIGH as a proof-of-existence artifact for continued commercial production into the CONVALCO era. **Museum/collection record:** **none found.** Searched directly against the Smithsonian, Winterthur, and Mercer Museum collections; no accession-numbered Forstner bit was located in any of them. Flagged explicitly as a genuine, checked absence — a real gap in this entry's proof record, not glossed over, and a contrast with several other tools in this corpus that do carry a museum-held example. **Ongoing patent activity (proof the form is still being refined):** multiple 20th–21st-century Forstner-specific patents were found in a Google Patents search (e.g., US6354774B1 and US7648316B2, both titled "Forstner drill bit," plus a 2024-era cylindrical-head boring-tool patent) — existence only, none read in full this run. Cited only as evidence the geometry remains a live area of patent activity across 150 years, corroborating the Wave Cutter and Bormax proprietary-geometry claims above. --- ## references | Title | Author/Source | URL | Kind | |---|---|---|---| | Benjamin Forstner | Wikipedia | en.wikipedia.org/wiki/Benjamin_Forstner | tertiary/encyclopedic | | US155148A — Improvement in Augers | Benjamin Forstner / DATAMP; Google Patents | datamp.org/patents/displayPatent.php?pn=155148&id=7965; patents.google.com/patent/US155148A | patent, primary — text read on Google Patents 2026-10-16 | | US336709A — Auger | Benjamin Forstner / Google Patents | patents.google.com/patent/US336709 | patent, read verbatim this run | | CA23548 — Auger | Benjamin Forstner / Espacenet (via Wikipedia citation) | — | patent, secondary citation only | | The Connecticut Valley and Centerbrook Manufacturing Companies | Randy Roeder / oldtoolheaven.com | oldtoolheaven.com/auger-bits/conn-valley.html | named tool historian, already trusted in this corpus (Auger, Brace and Bit) | | Need a Better Bit? Use the Forstner (trade catalog) | Connecticut Valley Manufacturing Co. / Internet Archive | archive.org/details/ConnValleyMfgCoForstnerBits | period trade catalog, scanned primary | | Tool Test: Forstner Bits | Roland Johnson / Fine Woodworking #197, Mar/Apr 2008 | finewoodworking.com/2008/03/01/tool-test-forstner-bits | trade press, named contributing editor, 18-brand comparative test | | Forstner Bits Basics | Bruce Kieffer / Popular Woodworking | popularwoodworking.com/tools/forstner-bits | trade press, named author | | Large Forstner Bits.. Exposing the MYTH | John Thompson ("Sarge"), Wilbur Pan / Sawmill Creek, 2009 | sawmillcreek.org/threads/large-forstner-bits-exposing-the-myth.101074 | forum, named posters, hands-on RPM test | | Forstner bit problems | Dave Mount, Richard Coers, John K. Jordan, Prashun Patel / Sawmill Creek, 2020 | sawmillcreek.org/threads/forstner-bit-problems.282879 | forum, named posters | | 3" forstner bit jamming | badger1805, Myko, derekcohen / Fine Woodworking forum, 2022 | finewoodworking.com/forum/3-forstner-bit-jamming | forum, named posters — derekcohen cross-corroborated in this corpus's Holdfast entry | | Forstner Bit RPM Chart | KM Tools | kmtools.com/products/forstner-bit-rpm-chart | manufacturer/retailer product, confirmed live, data image-only — no longer used for speed guidance (round 2) | | G0756 drill press owner's manual | Grizzly Industrial | cdn1.grizzly.com/manuals/g0756_m.pdf | machine maker's manual, primary — workholding, startup, chuck key, entanglement, eye/face, slow-large-bit grab (fetched 2026-10-16) | | Drill operating/safety instructions (r00001v1) | Bosch | boschtools.com/us/en/ocsmedia/r00001v1.pdf | drill maker's manual, primary — bind response, reaction torque (fetched 2026-10-16) | | Drill operating/safety instructions (r00016v1) | Bosch | boschtools.com/us/en/ocsmedia/r00016v1.pdf | drill maker's manual, primary — auxiliary handle, body position, securing work, eye protection (fetched 2026-10-16) | | Drill operator's manual (58-14-1700d9) | Milwaukee Tool | documents.milwaukeetool.com/58-14-1700d9.pdf | drill maker's manual, primary — stalled bit (fetched 2026-10-16) | | 35mm hinge-boring Forstner bits | RokHardware, Milescraft, HardwareSource, D. Lawless Hardware | (multiple retailer pages) | retailer, primary, fetched in the original research — portable-installation Forstner-pattern bits only | | DIN 7483:2024-11 — Wood bits, Forstner bits and hinge boring bits | DIN / DIN Media | dinmedia.de/en/standard/din-7483/384106644 | standard, summary page fetched 2026-10-16 (standard text itself not read) | | Cylinder boring bit HW Z 2+2 | LEUCO | leuco.com/EN/US/Boring_Bits/Cylinder_Boring_Bits/Cylinder_Head_Drill_Bits_HW_Z_2_2/1000118337 | manufacturer, primary — production hinge boring bit (fetched 2026-10-16) | | Forstner Speed Grinder (family listing) | Fisch Tools | fisch-tools.com/en/produkte/0310fsg-forstner-speed-grinder | manufacturer, primary — Forstner and hinge-boring families named separately (fetched 2026-10-16) | | Wave Cutter Forstner Bit | Fisch Tools | fisch-tools.com/en/produkte/0317-wave-cutter-forstner-bit; product sheet fisch-tools.com/assets/documents/Produkte_0317E_BIT-Forstnerbohrer-Wave-Cutter.pdf | manufacturer, primary — DIN 7483G, wave edge; no 25%/30× figures found (fetched 2026-10-16) | | Forstner bits | Bosch | boschtools.com/us/en/forstner-bits-43523-ocs-ac | manufacturer, primary — "For portable drills or stationary machines" (fetched 2026-10-16) | | Set of 7 Imperial HSS Forstner Bits | Lee Valley | leevalley.com/en-us/shop/tools/power-tool-accessories/drill-bits/102814 | retailer, primary — HSS heat claim (fetched 2026-10-16) | | Wood Owl Bits | Lee Valley | leevalley.com/en-us/shop/tools/power-tool-accessories/drill-bits/75748-wood-owl-bits | retailer, primary — lead-screw/triple-flute contrast, not a Forstner (fetched 2026-10-16) | | Bormax cutting geometry | FAMAG | (manufacturer page) | manufacturer, primary | | Forstner Chain Corporation — History | forstnerbands.com | forstnerbands.com | disambiguation source, unrelated brand | | FORSTNER (Austrian sheet-metal machinery) | RoofersCoffeeShop industry profile | — | disambiguation source, unrelated company | --- ## The reviewer's corrections (11) - `BLOCKER` — 1. Separate Forstner bits from hinge/cylinder boring bits — Exact claim: “The 35 mm hinge-cup bit is not a separate tool” and “production cabinet shops use a purpose-ground 35 mm Forstner.” - `BLOCKER` — 2. Replace broad RPM bands with maker-specific selection guidance — Exact claim: “Typical ranges run from roughly 500–2400 RPM in softwood and 250–700 RPM in hardwood” and “If in doubt, choose the slower speed.” - `BLOCKER` — 3. Remove the unsupported aluminum-use recipe — Exact claim: The “Not For” section permits thin soft aluminum with a drill press, slowest RPM, lubricant, clamping, and incremental feed. - `BLOCKER` — 4. Rebuild the safety section from authoritative drill and drill-press guidance — Exact claim: “The documented injury record specific to Forstner bits is genuinely thin,” followed mainly by generic hand-drill kickback and wrist strain. - `BLOCKER` — 5. Correct the startup instruction — Exact claim: “On a drill press, touch the rim down and let it score a full circle before applying full feed pressure.” - `SHOULD-FIX` — 6. Correct the Wood Owl classification — Exact claim: Wood Owl/Star-M PTFE-coated triple-flute, lead-screw-style bits are included in the current Forstner market inventory. - `SHOULD-FIX` — 7. Correct the “no formal standard” claim — Exact claim: “No governing engineering standard found” and Forstner bits are a wood-trade tool “without the formal standardization of a metalworking drill.” - `SHOULD-FIX` — 8. Qualify cutter-material and overheating claims — Exact claim: “The standard HSS Forstner bit remains the baseline,” carbide “resists burning,” and overheating/burning “loses the bit's temper permanently.” - `SHOULD-FIX` — 9. Remove arbitrary portable-versus-stationary diameter thresholds — Exact claim: A drill press is “effectively mandatory” above roughly 1 inch, while a hand drill remains usable below 1–2 inches. - `SHOULD-FIX` — 10. Treat the “facing” method as unsupported specialist technique — Exact claim: For large holes, score a full-diameter circle, remove most waste with smaller bits, then return with the full-diameter Forstner bit for cleanup. - `MINOR` — 11. Verify or remove quantified Wave Cutter marketing claims — Exact claim: Fisch's Wave Cutter has “25% less cutting resistance” and can be resharpened “up to 30 times.”